Toyota RAV4 manuals

BMW 7 Series (G11/G12) 2015-2022 Owners Manuals: With Parking Assistant Plus: Surround View- With navigation system: activation points

BMW 7 Series (G11/G12) 2015-2022 Owners Manuals / Controls / Driver assistance systems / With Parking Assistant Plus: Surround View- With navigation system: activation points

Concept

Positions where Panorama View should switch on automatically can be stored as activation points provided that a GPS signal is received.

General information

Up to ten activation points can be stored.

Activation points can be used when driving forward for the front camera.

Storing activation points

  1. Drive to the position at which the system is to be switched on, and stop.
  2. Press the button.

  3. Move the Controller to the right.
  4. "Activation point" The current position is displayed.
  5.  "Save activation point"

Activation points are, if possible, stored with town/city and street address, or else with the GPS coordinates.

Using activation points

The use of activation points can be switched on and off.

  1. Press the button.

  2. Move the Controller to the right.
  3.   "Settings"

  4. "Panorama View, GPS-based"
  5. "Panorama View is displayed automatically when set activation points are reached."

Displaying activation points

  1. Press the button.

  2.  Move the Controller to the right.
  3. "Manage points"

A list of all activation points is displayed.

Renaming or deleting activation points

  1. Press the button.

  2. Move the Controller to the right.
  3. "Manage points"
    A list of all activation points is displayed.
  4. Select an activation point as needed.
  5.  To perform the desired setting:

Setting brightness and contrast

Brightness and contrast can be adjusted with Surround View or Panorama View switched on.

Via iDrive:

  1. Move the Controller to the right, if needed.
  2. "Camera image"

  3. To perform the desired setting:

Functional limitations

The system can be used only to a limited extent in the following situations:

Gray hatched areas with symbol, for instance open door, in the camera image mark areas that are currently not displayed.

With Parking Assistant Plus: Surround View- System limits

Non-visible areas

Because of the camera angle, the areas under the vehicle cannot be viewed by the cameras.

Detection of objects

Very low obstacles as well as high, protruding objects such as ledges may not be detected by the system.

Some assistance functions also consider data from the PDC Park Distance Control.

Follow the notes in the PDC Park Distance Control chapter.

The objects displayed on the Control Display may be closer than they appear. Do not estimate the distance from the objects on the display.

Additional information: PDC Park Distance Control

Malfunction

A camera malfunction is displayed on the Control Display.

A yellow symbol is displayed and
the recording range of the malfunctioning camera is displayed in black on the Control Display.

With Parking Assistant Plus: Surround View- Panorama View
Concept The system provides an early look at cross traffic at blind driveways and intersections. General information Road users concealed by obstacles to the left and right of the vehicle can only b ...

With Parking Assistant Plus: Remote 3D View
Concept With the proper equipment, the BMW Connected App and the camera images from Surround View can be used to display the vehicle surroundings on a mobile device such as a smartphone. The function ...

Other materials:

On-vehicle inspection
Check throttle body Check the throttle control motor operating sounds. Turn the ignition switch on. When pressing the accelerator pedal, check the operating sound of the running motor. Make sure that no friction noises emit from the motor. If friction noise exists, replace t ...

Data list / active test (2005/11-2006/01)
Read data list Hint: Using the intelligent tester's data list allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the data list early in troubleshooting is one way to save time. Connect the intelligent tester (with can vim) to the ...

Main body ecu communication stop mode
Description Wiring diagram Inspection procedure Notice: Turn the ignition switch off before measuring the resistances of the main wire and the branch wire. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning syste ...

В© 2011-2022 Copyright www.trav4.net