Toyota RAV4 manuals

Toyota RAV4 Service Manual: Camshaft position "A"

Dtc

P0011 Camshaft position "a" - timing over-advanced or system performance (bank 1)

Dtc 

P0012 Camshaft position "a" - timing over-retarded (bank 1)

Description

The vvt system includes the ecm, oil control valve (ocv) and vvt controller. The ecm sends a target duty-cycle control signal to the ocv. This control signal regulates the oil pressure supplied to the vvt controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ecm controls the ocv, based on the signals transmitted by several sensors. The vvt controller regulates the intake camshaft angle using oil pressure through the ocv. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ecm detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ecm.

Toyota RAV4. Dtc  p0012 camshaft position "a" - timing over-retarded (bank 1)


Toyota RAV4. Dtc p0011 camshaft position "a"


Monitor description

The ecm optimizes the intake valve timing using the vvt (variable valve timing) system to control the intake camshaft. The vvt system includes the ecm, the oil control valve (ocv) and the vvt controller.

The ecm sends a target duty-cycle control signal to the ocv. This control signal regulates the oil pressure supplied to the vvt controller. The vvt controller can advance or retard the intake camshaft.

If the difference between the target and actual intake valve timings is large, and changes in the actual intake valve timing are small, the ecm interprets this as the vvt controller stuck malfunction and sets a dtc.

Example:

A dtc is set when the following conditions 1, 2 and 3 are met:

  1. The difference between the target and actual intake valve timing is more than 5°ca (crankshaft angle) and the condition continues for more than 4.5 Seconds.
  2. It takes 5 seconds or more to change the valve timing by 5°ca.
  3. After above conditions 1 and 2 are met, the ocv is forcibly activated 63 times or more.

Dtc p0011 (advanced cam timing) is subject to 1 trip detection logic.

Dtc p0012 (retarded cam timing) is subject to 2 trip detection logic.

These dtcs indicate that the vvt controller cannot operate properly due to ocv malfunctions or the presence of foreign objects in the ocv.

The monitor will run if all of the following conditions are met:

Monitor strategy

Toyota RAV4. Monitor strategy


Typical enabling conditions

Toyota RAV4. Typical enabling conditions


Typical malfunction thresholds

Advanced camshaft timing:


Retard camshaft timing:


If the difference between the target and actual camshaft timings is greater than the specified value, the ecm operates the vvt actuator.

Then, the ecm monitors the camshaft timing change for 5 seconds.

Wiring diagram

Refer to dtc p0010 (see page es-64).

Inspection procedure

Notice:

Dtc p0011 or p0012 may be set when foreign objects in the engine oil are caught in some parts of the system. The dtc will remain set even if the system returns to normal after a short time.

Foreign objects are filtered out by the oil filter.

Hint:

If dtc p0011 or p0012 is present, check the vvt (variable valve timing) system.

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  1. Check any other dtcs output (in addition to dtc p0011 or p0012)

  1. Connect the intelligent tester to the dlc3.
  2. Turn the ignition switch on and turn the tester on.
  3. Select the following menu items: diagnosis / enhanced obd ii / dtc info / current codes.
  4. Read dtcs.

Toyota RAV4. Check any other dtcs output (in addition to dtc p0011 or p0012)


Toyota RAV4. Check any other dtcs output (in addition to dtc p0011 or p0012)


  1. Perform active test using intelligent tester (operate ocv)

  1. Connect the intelligent tester to the dlc3.
  2. Start the engine and turn the tester on.
  3. Warm up the engine.
  4. On the tester, select the following menu items: diagnosis / enhanced obd ii / active test / vvt ctrl b1.
  5. Check the engine speed while operating the oil control valve (ocv) using the tester.

Toyota RAV4. Perform active test using intelligent tester (operate ocv)


  1. Check whether dtc output recurs (dtc p0011 or p0012)

  1. Connect the intelligent tester to the dlc3.
  2. Turn the ignition switch on and turn the tester on.
  3. Clear dtcs (see page es-35).
  4. Start the engine and warm it up.
  5. Switch the ecm from normal mode to check mode using the tester.
  6. Drive the vehicle for more than 10 minutes.
  7. Read dtcs using the tester.

Ok: no dtc output.

Toyota RAV4. Check whether dtc output recurs (dtc p0011 or p0012)


  1. Check valve timing (check for loose and jumped teeth on timing chain)

Toyota RAV4. Check valve timing (check for loose and jumped teeth on timing chain)


  1. Remove the cylinder head cover.
  2. Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.
  3. Check that the timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward as shown in the illustration.

    If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

Ok:

Timing marks on camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover.

Toyota RAV4. Check valve timing (check for loose and jumped teeth on timing chain)


  1. Inspect camshaft timing oil control valve assembly (ocv)


  1. Remove the ocv.
  2. Measure the resistance between the terminals of the ocv.

Standard resistance: 6.9 To 7.9 Ù at 20°c (68°f)

  1. Apply the positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.

Ok: valve moves quickly.

  1. Reinstall the ocv.

Toyota RAV4. Inspect camshaft timing oil control valve assembly (ocv)


  1. Inspect oil control valve filter


  1. Remove the generator.
  2. Remove the ocv filter.
  3. Check that the filter is not clogged.

Ok: filter is not clogged.

  1. Reinstall the ocv filter.
  2. Reinstall the generator.


  1. Replace camshaft timing gear assembly


  1. Check whether dtc output recurs

  1. Connect the intelligent tester to the dlc3.
  2. Turn the ignition switch on and turn the tester on.
  3. Clear dtcs (see page es-35).
  4. Start the engine and warm it up.
  5. Switch the ecm from normal mode to check mode using the tester.
  6. Drive the vehicle for more than 10 minutes.
  7. Read output dtcs using the tester.

Standard: no dtc output.

Hint:

Dtc p0011 or p0012 is output when foreign objects in engine oil are caught in some parts of the system. These codes will stay registered even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.

Toyota RAV4. Check whether dtc output recurs


Camshaft position "a" actuator circuit (bank 1)
Dtc P0010  Camshaft position "a" actuator circuit (bank 1) Description The variable valve timing (vvt) system includes the ecm, ocv and vvt controller. The ecm sends a target du ...

Camshaft position correlation (bank 1 sensor a)
Dtc P0016 P0016 crankshaft position - camshaft position correlation (bank 1 sensor a) Description In the vvt (variable valve timing) system, the appropriate intake valve open and close timing is ...

Other materials:

Precaution
Check that the battery cables are connected to the correct terminals. Disconnect the battery cables if a quick charge is given to the battery. Do not perform tests with a high voltage insulation resistance tester. Never disconnect the battery while the engine is running. Check tha ...

Engine (ignition) switch (vehicles with a smart key system)
Performing the following operations when carrying the electronic key on your person starts the engine or changes engine switch modes. Starting the engine Check that the parking brake is set. Check that the shift lever is set in p. Firmly depress the brake pedal. The smart key system in ...

Voice settings
This screen is used for setting the voice command guidance system. Adjust the voice guidance volume setting. Set the voice recognition prompts “high”, “low” or “off”. Train voice recognition Set the voice prompt interrupt on/off. Voice recognition tutorial To re ...

© 2011-2024 Copyright www.trav4.net