Toyota RAV4 Service Manual: Compressor and pulley (for 2gr-fe)
Components
Removal
- Discharge refrigerant from
refrigeration system (see page ac-172)
- Disconnect cable from negative battery
terminal
Caution:
Wait at least 90 seconds after disconnecting the
cable from the negative (-) battery terminal to
prevent airbag and seat belt pretensioner activation.
- Disconnect no. 1 Cooler refrigerant suction hose
- Remove the bolt and disconnect the cooler
refrigerant suction hose from the cooler compressor.
- Remove the o-ring from the cooler refrigerant
suction hose.
Notice:
Seal the openings of the disconnected parts
using vinyl tape to prevent moisture and foreign
matter from entering them.
- Disconnect no. 1 Cooler refrigerant discharge hose
- Remove the bolt and disconnect the cooler
refrigerant discharge hose from the cooler
compressor.
- Remove the o-ring from the cooler refrigerant
discharge hose.
Notice:
Seal the openings of the disconnected parts
using vinyl tape to prevent moisture and foreign
matter from entering them.
- Remove fan and generator v belt (see page
em-8)
- Remove cooler compressor assembly
- Disconnect the connector.
- Remove the 4 bolts and cooler compressor.
Installation
- Install cooler compressor assembly
- Install the cooler compressor with the 4 bolts.
Torque: 24.5 N*m (250 kgf*cm, 18 ft.*Lbf)
Notice:
Tighten the bolts in the order shown in the
illustration to install the cooler compressor.
- Connect the connector.
- Connect no. 1 Cooler refrigerant discharge hose
- Remove the attached vinyl tape from the hose.
- Sufficiently apply compressor oil to a new o-ring
and the fitting surface of the cooler compressor.
Compressor oil:
nd-oil 8 or equivalent
- Install the o-ring to the cooler refrigerant discharge
hose.
- Connect the cooler refrigerant discharge hose to the
cooler compressor with the bolt.
Torque: 9.8 N*m (100 kgf*cm, 7 ft.*Lbf)
- Connect no. 1 Cooler refrigerant suction hose
- Remove the attached vinyl tape from the hose.
- Sufficiently apply compressor oil to a new o-ring
and the fitting surface of the cooler compressor.
Compressor oil:
nd-oil 8 or equivalent
- Install the o-ring to the cooler refrigerant suction
hose.
- Connect the cooler refrigerant suction hose to the
cooler compressor with the bolt.
Torque: 9.8 N*m (100 kgf*cm, 7 ft.*Lbf)
- Install fan and generator v belt (see page
em-8)
- Connect cable to negative battery
terminal
- Charge refrigerant (see page ac-172)
- Warm up engine (see page ac-173)
- Check for leakage of refrigerant (see
page ac-173)
Components
Removal
Discharge refrigerant from
refrigeration system (see page ac-172)
Disconnect cable from negative battery
terminal
Caution:
Wait at least 90 seconds after disconne ...
Components
On-vehicle inspection
Inspect cooler condenser assembly
If the fins of the cooler condenser are dirty, clean
them with water. Dry the fins with compressed air.
Notic ...
Other materials:
Srs warning light remains on
Description
The srs warning light is located on the combination meter.
When the srs is normal, the srs warning light comes on for approximately 6
seconds after the ignition
switch is turned from off to on, and then goes off automatically.
If there is a malfunction in the srs, the srs warni ...
Adjusting the settings manually
To adjust the fan speed, press
on
to increase the fan
speed and to
decrease the fan speed.
Press to turn the fan off.
To adjust the temperature setting, turn
clockwise to
increases the temperature and turn
counterclockwise to
...
Only rear door lh lock / unlock functions do not operate
Description
The main body ecu receives lock / unlock switch signals and activates the
door lock motor accordingly.
Wiring diagram
Inspection procedure
Inspect rear door with motor lock assembly lh
Apply the battery voltage to the door lock motor and
check the operation of th ...