Toyota RAV4 Service Manual: Disassembly (2005/11-2006/01)
- Remove front axle inboard joint boot no. 2
Clamp lh
- One touch type:
- Using a screwdriver, remove the no. 2 Inboard
joint boot clamp, as shown in the illustration.
- Claw engagement type:
Using needle-nose pliers, remove the no. 2
Inboard joint boot clamp, as shown in the
illustration.
- Remove front axle inboard joint boot no.
2 Clamp rh
Hint:
Using needle-nose pliers, remove the no. 2 Inboard joint
boot clamp, as shown in the illustration.
- Remove front axle inboard joint boot clamp lh
- One touch type:
- Using a screwdriver, remove the inboard joint
boot clamp, as shown in the illustration.
- Claw engagement type:
Using needle-nose pliers, remove the inboard
joint boot clamp, as shown in the illustration.
- Remove front axle inboard joint boot
clamp rh
Hint:
Use the same procedures described for the lh side.
- Remove front axle inboard joint boot
- Remove the boot from the inboard joint.
- Remove front drive inboard joint assembly lh
- Remove any old grease from the inboard joint.
- Put matchmarks on the inboard joint and outboard
joint shaft.
Notice:
Do not punch the marks.
- Remove the inboard joint from the outboard joint
shaft.
- Using a snap ring expander, remove the shaft snap
ring.
- Put matchmarks on the outboard joint shaft and
tripod joint.
Notice:
Do not punch the marks.
- Using a brass bar and hammer, tap out the tripod
joint from the outboard joint shaft.
Notice:
Do not tap the rollers.
- Remove the inboard joint boot.
- Remove front drive shaft damper clamp lh
- One touch type:
- Using a screwdriver, remove the drive shaft
damper clamp, as shown in the illustration.
- Claw engagement type:
- Using needle-nose pliers, remove the drive
shaft damper clamp, as shown in the
illustration.
- Remove front drive shaft damper lh
- Remove the front drive shaft damper.
- Remove front drive shaft damper clamp rh
Hint:
Use the same procedures described for the lh side.
- Remove front drive shaft damper rh
Hint:
Use the same procedures described for the lh side.
- Remove front axle outboard joint boot no. 2
Clamp lh
- Using a screwdriver, remove the no. 2 Outboard
joint boot clamp, as shown in the illustration.
- Remove front axle outboard joint boot clamp lh
- Using a screwdriver, remove the outboard joint boot
clamp, as shown in the illustration.
- Remove front axle outboard joint boot
- Remove the outboard joint boot from the outboard
joint shaft.
- Remove any old grease from the outboard joint.
- Remove front drive shaft hole snap ring lh
- Using a screwdriver, remove the hole snap ring.
- Remove front drive shaft dust cover lh
- Using sst and a press, press out the front drive
shaft dust cover.
Sst 09950-00020
Notice:
Be careful not to drop the inboard joint
- Remove front drive shaft dust cover rh
- Using a press, press out the drive shaft dust cover.
- Remove front drive shaft bearing
- Using a snap ring expander, remove the drive shaft
hole snap ring.
- Using sst and a press, press out the drive shaft
bearing.
Sst 09527-10011
- Remove the snap ring.
Remove front wheel
Drain automatic transaxle fluid
Drain the automatic transaxle fluid for u140f (see
page ax-147).
Drain the automatic transaxle fluid for u241e (see
page ax-146).
...
Remove front axle inboard joint boot no. 2
Clamp
One touch type:
using a screwdriver, remove the no. 2 Inboard joint
boot clamp, as shown in the illustration.
Claw engagement typ ...
Other materials:
All doors cannot be locked / unlocked simultaneously
Description
The main body ecu receives switch signals from the door control switch on the
power window regulator
master switch, door control switch and driver side door key cylinder, and
activates the door lock motor on
each door accordingly.
Wiring diagram
Inspection procedure
Perf ...
Check for open circuit
For an open circuit in the wire harness in fig. 1,
Check the resistance or voltage, as described below.
Check the resistance.
Disconnect connectors a and c, and measure
the resistance between them.
Standard resistance (fig. 2)
Hint:
Measure the resistance while lightly s ...
Position initialization incomplete
Description
This dtc is output when the sliding roof drive gear (sliding roof ecu) has
not been initialized.
Wiring diagram
Refer to dtc b2341 (see page rf-11).
Inspection procedure
Initialize sliding roof drive gear sub-assembly (sliding roof ecu)
Check that the sliding roof ...