Toyota RAV4 manuals

Toyota RAV4 Service Manual: For vehicles with supplemental restraint system

Toyota RAV4 Service Manual / Introduction / Repair instruction / Precaution / For vehicles with supplemental restraint system

The rav4 is equipped with a supplemental restraint system (srs). The srs of this vehicle consists of the following:

  1. Steering pad
  2. Front passenger airbag assembly
  3. Front seat side airbag assembly
  4. Front seat outer belt assembly with pretensioner
  5. Curtain shield
  6. Center airbag sensor
  7. Front airbag sensor
  8. Side airbag sensor
  9. Rear airbag sensor
  10. Occupant classification ecu

Caution:

Notice:

  1. Spiral cable

  1. The steering wheel must be fitted correctly to the steering column with the spiral cable at the neutral position, as cable disconnection and other problems may occur. Refer to the information about correct installation of the steering wheel.
  1. Airbag assembly

  1. Airbag assembly with pad: always place a removed or new airbag assembly with the pad surface facing upward.

    Placing the airbag assembly with the airbag inflation direction facing downward could cause a serious accident if the airbag inflates. Also, do not place anything on top of the airbag assembly.

  2. Never measure the resistance of the airbag squib. This may cause the airbag to inflate, which could cause a serious injury.
  3. Grease or detergents of any kind should not be applied to the airbag assembly.
  4. Store the airbag assembly in an area where the ambient temperature is below 93°c (200°f), the humidity is not high and there is no electrical noise.
  5. When using electric welding anywhere on the vehicle, disconnect the airbag ecu connectors.

    These connectors contain shorting springs. This feature reduces the possibility of the airbag deploying due to currents entering the squib wiring.

  6. When disposing of the vehicle or the airbag assembly by itself, the airbag should be deployed using sst before disposal. Activate the airbag in a safe place away from electrical noise.
  1. Seat outer belt assembly with pretensioner

  1. Never measure the resistance of the seat outer belt. This may cause the pretensioner of the seat outer belt to activate, which could cause a serious injury
  2. Never install the seat outer belt on another vehicle.
  3. Store the seat outer belt in an area where the ambient temperature is below 80°c (176°f), the humidity is not high and there is no electrical noise.
  4. When using electric welding anywhere on the vehicle, disconnect the airbag ecu connectors (2 pins). These connectors contain shorting springs. This feature reduces the possibility of the pretensioner deploying due to currents entering the squib wiring.
  5. When disposing of a vehicle or the seat outer belt by itself, the pretensioner should be activated before disposal. Activate the pretensioner in a safe place away from electrical noise.
  6. As the seat outer belt is hot after the pretensioner is activated, allow some time for it to cool down sufficiently before disposal. Never apply water to try to cool down the seat outer belt.
  7. Grease, detergents, oil or water should not be applied to the seat outer belt.
  1. Airbag sensor assembly

  1. Never reuse an airbag sensor assembly that has been involved in a collision where the srs has deployed.
  2. The connectors to the airbag sensor assembly should be connected or disconnected with the sensor placed on the floor. If the connectors are connected or disconnected while the airbag sensor assembly is not placed on the floor, the srs may activate.
  3. Work must be started at least 90 seconds after the ignition switch is turned off and the cable is disconnected from the negative (-) battery terminal, even if only loosening the set bolts of the airbag sensor assembly.
  1. Wire harness and connector

  1. The srs wire harness is integrated with the instrument panel wire harness assembly. All the connectors in the system are yellow. If the srs wire harness becomes disconnected or the connector becomes broken, repair or replace it.
Basic repair hint
Hints on operations 1 Attire Always wear a clean uniform. A hat and safety shoes must be worn. 2 Vehicle protection Prepare a grille cover, f ...

Electronic control
Removal and installation of battery terminal Notice: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal. Be ...

Other materials:

Front lower ball joint
Components Removal Hint: Use the same procedures for the rh side and lh side. The procedures listed below are for the lh side. Remove front wheel Remove front speed sensor lh (for 2wd) (see page bc-191) Remove front brake cylinder assembly lh (see page br-40) Remove front ...

Listening to an ipod
Connecting an ipod enables you to enjoy music from the vehicle speakers. Select “ipod” on the audio source selection screen. When the ipod connected to the system includes ipod video, the system can only output the sound by selecting the browse screen. Connecting an ipod Audio control ...

Terminals of ecu (2006/01- )
Check air conditioning amplifier Measure the voltage and resistance of the connectors. Hint: Check from the rear of the connector while it is connected to the air conditioning amplifier. Hint: *: For 2gr-fe Using an oscilloscope, check waveform 1. Can communi ...

© 2011-2024 Copyright www.trav4.net