Toyota RAV4 manuals

Toyota RAV4 Service Manual: Front occupant classification sensor lh collision detection

Toyota RAV4. Front occupant classification sensor lh collision detection


Description

Dtc b1785 is output when the occupant classification ecu receives a collision detection signal sent by the front occupant classification sensor lh when an accident occurs.

Dtc b1785 is also output when the front seat rh is subjected to a strong impact, even if an actual accident does not occur.

However, when the occupant classification ecu outputs a collision detection signal, even if the vehicle is not in a collision, dtc b1785 can be cleared by performing the zero point calibration and sensitivity check.

Therefore, when dtc b1785 is output, first perform the zero point calibration and sensitivity check.

Toyota RAV4. Front occupant classification sensor lh collision detection


Wiring diagram

Toyota RAV4. Front occupant classification sensor lh collision detection


Inspection procedure

  1. Perform zero point calibration

  1. Connect the intelligent tester (with can vim) to the dlc3.
  2. Turn the ignition switch on.
  3. Using the intelligent tester, perform the zero point calibration (see page rs-241).

Ok: completed is displayed.



  1. Perform sensitivity check

  1. Using the intelligent tester, perform the sensitivity check (see page rs-241).

Standard value: 27 to 33 kg (59.52 To 72.75 Lb)



  1. Check for dtc

  1. Turn the ignition switch on.
  2. Clear the dtcs (see page rs-249).

Hint:

First clear dtcs stored in the occupant classification ecu and then in the center airbag sensor.

  1. Turn the ignition switch off.
  2. Turn the ignition switch on.
  3. Check the dtcs (see page rs-249).

Ok: dtc b1785 is not output.

Hint:

Dtcs other than dtc b1785 may be output at this time, but they are not related to this check.



  1. Replace front seat assembly rh

  1. Turn the ignition switch off.
  2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
  3. Replace the front seat rh (see page se-8).

Hint:

Perform the inspection using parts from a normal vehicle if possible.


  1. Perform zero point calibration

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
  2. Connect the intelligent tester (with can vim) to the dlc3.
  3. Turn the ignition switch on.
  4. Using the intelligent tester, perform the zero point calibration (see page rs-241).

Ok: completed is displayed.


  1. Perform sensitivity check

  1. Using the intelligent tester, perform the sensitivity check (see page rs-241).

Standard value: 27 to 33 kg (59.52 To 72.75 Lb)


  1. Check for dtc

  1. Turn the ignition switch on.
  2. Clear the dtcs (see page rs-249).

Hint:

First clear dtcs stored in the occupant classification ecu and then in the center airbag sensor.

  1. Turn the ignition switch off.
  2. Turn the ignition switch on.
  3. Check the dtcs (see page rs-249).

Ok: dtc b1785 is not output.

Hint:

Dtcs other than dtc b1785 may be output at this time, but they are not related to this check.



  1. Replace occupant classification ecu

  1. Turn the ignition switch off.
  2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
  3. Replace the occupant classification ecu (see page se- 8).


  1. Perform zero point calibration

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
  2. Connect the intelligent tester to the dlc3.
  3. Turn the ignition switch on.
  4. Using the intelligent tester, perform the zero point calibration (see page rs-241).

Ok: completed is displayed.


  1. Perform sensitivity check

  1. Using the intelligent tester, perform the sensitivity check (see page rs-241).

Standard value: 27 to 33 kg (59.52 To 72.75 Lb)


End

Rear occupant classification sensor rh circuit malfunction
Description The rear occupant classification sensor rh circuit consists of the occupant classification ecu and the rear occupant classification sensor rh. Dtc b1783 is recorded when a malf ...

Front occupant classification sensor rh collision detection
Description Dtc b1786 is output when the occupant classification ecu receives a collision detection signal sent by the front occupant classification sensor rh when an accident occurs. Dtc b ...

Other materials:

Combination meter ecu communication stop mode
Description Wiring diagram Inspection procedure Notice: Turn the ignition switch off before measuring the resistances of the main wire and the branch wire. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system ...

Child restraint seat tether anchor
Components Removal Remove child restraint seat tether anchor cover Using a screwdriver, detach the 4 claws and remove the cover. Hint: Tape the screwdriver tip before use. Remove roof headlining assembly Hint: It is not necessa ...

Brake booster
Installation (2005/11-2006/01) Install check valve grommet Install the grommet to the booster. Install brake vacuum check valve assembly Install the check valve to the grommet. Install brake booster gasket Install a new gasket to the booster. Install brake ...

В© 2011-2024 Copyright www.trav4.net