Toyota RAV4 manuals

Toyota RAV4 Service Manual: Fuel pump control circuit

Description

When the engine is cranked, the starter relay drive signal output from the star terminal of the ecm is input into the sta terminal of the ecm, and ne signal generated by the crankshaft position sensor is also input into the ne+ terminal. Thus, the ecm interprets that the engine is cranked, and turns the transistor tr1 in the ecm internal circuit on. The current flows to the c/opn (circuit opening) relay by turning the tr1 on. Then, the fuel pump operates.

While the ne signal is input into the ecm, when the engine is running, the ecm turns the tr1 on continuously.

Toyota RAV4. Fuel pump control circuit


Wiring diagram

Toyota RAV4. Wiring diagram


Inspection procedure

  1. Perform active test using intelligent tester (fuel pump/spd)

  1. Connect the intelligent tester to the dlc3.
  2. Turn the ignition switch on and turn the tester on.
  3. Select the following menu items: diagnosis / enhanced obd ii / active test / fuel pump / spd.
  4. Check whether the fuel pump operating sound occurs when performing the active test on the tester.

Ok: fuel pump operating sound occurs.



  1. Inspect instrument panel junction block assembly (c/opn relay input voltage)

  1. Measure the voltage between the terminal of the instrument panel junction block (j/b) and the body ground when the ignition switch is turned on and off.

Standard voltage




  1. Check harness and connector (instrument panel j/b - integration relay, ig2 relay)

  1. Remove the integration relay and ig2 relay from the engine room no. 1 Relay block.
  2. Disconnect the instrument panel junction block connector.
  3. Check the resistance.

Standard resistance (check for open)


Standard resistance (check for short)


  1. Reinstall the integration relay and ig2 relay.
  2. Reconnect the instrument panel junction block connector.



  1. Inspect instrument panel junc.ssembly (c/opn relay)

  1. Remove the instrument panel junction block.
  2. Measure the c/opn relay resistance.

Standard resistance


Hint:

Relay coil circuit between if-4 and ie-5 is not through ign fuse.

  1. Reinstall the instrument panel junction block.



  1. Check harness and connector (instrument panel j/b - ecm)

  1. Disconnect the a9 ecm connector.
  2. Disconnect the ie connector from instrument panel junction block.
  3. Measure the resistance.

Standard resistance (check for open)


Standard resistance (check for short)


  1. Reconnect the instrument panel junction block and the ecm connectors.



  1. Check harness and connector (c/opn relay - fuel pump - body ground)

  1. Check the harness and the connectors between the instrument panel junction block assembly and the fuel pump.
  1. Disconnect the ia instrument panel junction block connector.
  2. Disconnect the s1 fuel pump connector.
  3. Measure the resistance.

Standard resistance (check for open)


Standard resistance (check for short)


  1. Check the harness and the connectors between the fuel pump and the body ground.
  1. Disconnect the s1 fuel pump connector.
  2. Measure the resistance.

Standard resistance (check for open)


  1. Reconnect the instrument panel junction block connector
  2. Reconnect the fuel pump connector.



  1. Inspect fuel pump

  1. Inspect fuel pump resistance.

  1. Measure the resistance between the terminals.

Standard resistance: 0.2 To 3.0 ٠at 20°c(68°f)

  1. Inspect fuel pump operation.
  1. Apply the battery voltage to both the terminals.

Notice:




  1. Read value using intelligent tester (starter sig)

  1. Connect the intelligent tester to the dlc3.
  2. Turn the ignition switch on and turn the tester on.
  3. Select the following menu items: diagnosis / enhanced obd ii / data list / primary / starter sig.
  4. Check the result when the ignition switch is turned to on and start.

Ok




  1. Read value using intelligent tester (engine spd)

  1. Connect the intelligent tester to the dlc3.
  2. Turn the ignition switch on and turn the tester on.
  3. Select the following menu items: diagnosis / enhanced obd ii / data list / primary / engine spd.
  4. Read the values displayed on the tester while cranking.

Standard: values are displayed continuously.



Vc output circuit
Description The ecm constantly generates 5 v power from the battery voltages supplied to the +b (batt) terminal to operate the microprocessor. The ecm also provides this power to the sensors thr ...

Mil circuit
Description The mil (malfunction indicator lamp) is used to indicate vehicle malfunction detections by the ecm. When the ignition switch is turned on, power is supplied to the mil circuit, and ...

Other materials:

Reassembly
Install piston Using a small screwdriver, install a new snap ring onto one end of the piston pin hole. Hint: Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston. Gradually heat the piston up to 80 to 90°c (176 to 194°f ...

Disassembly
Caution: Wear protective gloves. Sharp areas on the seat frame (with adjuster) may injure your hands. Remove reclining power seat switch knob Using a screwdriver, detach the knob. Hint: Tape the screwdriver tip before use. Remove slide and vertical power seat switch knob ...

Customer problem analysis
Hint: In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem an ...

© 2011-2024 Copyright www.trav4.net