Toyota RAV4 Service Manual: Illumination circuit
Description
The main body ecu receives information regarding the door courtesy switch and
door lock position
switch, and turns on the room light.
Wiring diagram
Inspection procedure
- Perform active test by intelligent tester (main body ecu)
- Connect the intelligent tester (with can vim) to the
dlc3.
- Turn the ignition switch to the on position and press the
intelligent tester main switch on.
- Select the items below in the active test and then
check the main body ecu operation.
Ok:
light comes on.
- Inspect fuse (dome)
- Remove the dome fuse from the engine room no. 2
Relay block.
- Measure the resistance of the fuse.
Standard resistance:
below 1
- Inspect room light assembly
- Remove the room light assembly
- Measure the resistance of the room light switch base.
Standard resistance
- Inspect room light bulb
- Remove the room light assembly.
- Connect the positive (+) lead from the battery to terminal
1 and the negative (-) lead to terminal 2, then check that
the light comes on when the switch is in the door
position.
Ok:
light comes on.
- Connect the positive (+) lead from the battery to terminal
1 and the negative (-) lead to terminal 3, then check that
the light comes on when the switch is in the on position.
Ok:
light comes on.
- Check harness and connector (battery - room light and main body ecu)
- Disconnect the ik instrument panel junction block
connector.
- Measure the voltage of the wire harness side connector.
Standard voltage
- Inspect map light bulb
- Remove the map light assembly.
- Connect the positive (+) lead from the battery to terminal
6 and the negative (-) lead to terminal 1, then check that
the light comes on when the switch is in the door
position.
Ok:
light comes on.
- Connect the positive (+) lead from the battery to terminal
6 and the negative (-) lead to terminal 7, then check that
the light comes on when the switch is in the on position.
Ok:
light comes on.
- Inspect map light
- Replace the map light bulb with a normally functioning
one or a new one.
- Connect the positive (+) lead from the battery to terminal
6 and the negative (-) lead to terminal 1, then check that
the light comes on when the switch is in the door
position.
Ok:
light comes on.
- Connect the positive (+) lead from the battery to terminal
6 and the negative (-) lead to terminal 7, then check that
the light comes on when the switch is in the on position.
Ok:
light comes on.
Replace map light bulb
- Check wire harness (battery - map light and main body ecu)
- Disconnect the ik instrument panel junction block
connector.
- Measure the voltage of the wire harness side connector.
Standard voltage
- Inspect ignition key cylinder light
- W/ engine immobiliser system
- Remove the transponder key amplifier (ignition key
cylinder light).
- Connect the positive (+) lead from the battery to
terminal 2 and the negative (-) lead to terminal 6,
then check that the light comes on.
Ok:
light comes on.
- W/o engine immobiliser system
- Remove the ignition key cylinder light.
- Connect the positive (+) lead from the battery to
terminal 2 and the negative (-) lead to terminal 1,
then check that the light comes on.
Ok:
light comes on.
- Check wire harness (battery - main body ecu)
- Disconnect the ie instrument panel junction block
connector.
- Measure the voltage of the wire harness side connector.
Replace instrument panel junction block
Description
The main body ecu receives information regarding the door lock position
switch and ignition switch, and
turns on each foot light.
Wiring diagram
Inspection procedure
Perform ...
Description
When the light control switch, located on the headlight dimmer switch, is
turned to the tail position, the
taillight relay (marking: t-lp) turns on to illuminate the front side marker ...
Other materials:
Disassembly
Remove magnetic switch assembly
Remove the nut and disconnect the lead wire from
the magnetic switch.
Remove the 2 screws holding the magnetic switch
to the starter drive housing.
Remove the magnetic switch.
Remove the return spring and plunger from the
starter drive hou ...
Tire pressure warning valve and transmitter
Components
Removal
Remove front tire
Remove rear tire
Remove tire pressure warning valve subassembly
Remove the valve core and cap, and release air
from the tire.
After ensuring that air is sufficiently released,
remove the nut and washer that are used to fix the
tire pres ...
Trailer tongue weight
A recommended tongue weight varies in accordance with the types
of trailers or towing as described below.
To ensure the recommended values shown below, the trailer must
be loaded by referring to the following instructions.
Tongue weight
The gross trailer weight should be distributed so ...