Toyota RAV4 manuals

Toyota RAV4 Service Manual: Installation

  1. Install fuel filler opening lid lock retainer

Toyota RAV4. Install fuel filler opening lid lock retainer


  1. Install the lock retainer and turn it counterclockwise as shown in the illustration.
  1. Install fuel filler opening lid lock retainer

Toyota RAV4. Install fuel filler opening lid lock retainer


  1. Install the cable and turn it clockwise as shown in the illustration.
  2. Install the fuel lid lock open lever with the bolt.

    Torque: 8.0 N*m (82 kgf*cm, 71 in.*Lbf)

  3. Install the cable to the clamps as shown in the illustration.

Toyota RAV4. Install fuel filler opening lid lock retainer


  1. Install front floor carpet assembly

  2. Install deck trim side panel assembly rh (w/ rear no. 2 Seat) (see page ir-34)

  3. Install deck trim side panel assembly rh (w/o rear no. 2 Seat) (see page ir-53)

  4. Install deck trim side panel assembly lh (w/ rear no. 2 Seat) (see page ir-32)

  5. Install deck trim side panel assembly lh (w/ o rear no. 2 Seat) (see page ir-52)

  6. Install tether anchor bracket subassembly (w/o rear no. 2 Seat) (see page ir-54)

  7. Install reclining remote control lever bezel rh (w/o rear no. 2 Seat) (see page se-105)

  8. Install reclining remote control lever bezel lh (w/o rear no. 2 Seat) (see page se-73)

  9. Install rear deck trim cover rh (w/ rear no.

    2 Seat) (see page ir-55)

  10. Install rear deck trim cover lh (w/ rear no.

    2 Seat) (see page ir-55)

  11. Install rear floor finish plate (see page ir- 55)

  12. Install back door weatherstrip

  13. Install rear floor no. 1 Mat support side plate (see page ir-55)

  14. Install rear floor no. 2 Board

  15. Install rear floor no. 3 Board

  16. Install rear no. 2 Seat assembly rh (w/ rear no. 2 Seat)

  1. Install the rear no. 2 Seat (see page se-121).
  1. Install rear no. 2 Seat assembly lh (w/ rear no. 2 Seat)

  1. Install the rear no. 2 Seat (see page se-121).
  1. Install deck board assembly (w/o rear no. 2 Seat)

  2. Install rear floor no. 1 Board (w/o rear no.

    2 Seat)

  3. Install rear floor no. 1 Board (w/o rear no.

    2 Seat)

  4. Install package tray trim pocket subassembly (w/o rear no. 2 Seat)

  5. Install lower center pillar garnish rh (see page ir-56)

  6. Install lower center pillar garnish lh (see page ir-56)

  7. Install rear door opening trim weatherstrip rh

  8. Install rear door opening trim weatherstrip lh

  9. Install rear door scuff plate rh (see page ir-57)

  10. Install rear door scuff plate lh (see page ir-57)

  11. Install front door opening trim weatherstrip rh

  12. Install front door opening trim weatherstrip lh

  13. Install cowl side trim board rh (see page ir- 59)

  14. Install cowl side trim board lh (see page ir- 59)

  15. Install front door scuff plate rh (see page ir-59)

  16. Install front door scuff plate lh (see page ir-59)

  17. Install rear console box sub-assembly (see page ip-26)

  18. Install rear console box sub-assembly (see page ip-26)

  19. Install rear console box sub-assembly (see page ip-26)

  20. Install rear console box sub-assembly (see page ip-26)

  21. Install upper rear console panel subassembly (see page ip-27)

  22. Install upper rear console panel subassembly (see page ip-27)

  23. Install switch base (see page ip-27)

  24. Install upper console panel sub-assembly (see page ip-27)

  25. Install no. 2 Console upper panel garnish (see page ip-28)

  26. Install no. 1 Console upper panel garnish (see page ip-28)

  27. Install rear no. 1 Seat assembly lh

  1. Install the rear no. 1 Seat (see page se-64).
  1. Install rear no. 1 Seat assembly rh

  1. Install the rear no. 1 Seat (see page se-97).
  1. Install front seat assembly lh

  1. Install the front seat.

    For manual seat (see page se-22) for power seat (see page se-37).

  1. Install front seat assembly rh

  1. Install the front seat.

    For manual seat (see page se-22) for power seat (see page se-37)

  1. Connect cable to negative battery terminal

  2. Check srs warning light

  1. Check the srs warning light (see page rs-37).
Removal
Disconnect cable from negative battery terminal Caution: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt preten ...

Exterior
...

Other materials:

Cold start
Description The electronic throttle control system (etcs) controls the engine idling speed. The etcs operates the throttle actuator to open and close the throttle valve, and adjusts the intake air amount to achieve the target idling speed. In addition, the ecm retards the ignition timi ...

Diagnosis system
Description The center airbag sensor controls the functions of the supplemental restraint system (srs) on the vehicle. Data of the srs can be read in the data link connector 3 (dlc3) of the vehicle. When the system seems to be malfunctioning, use the intelligent tester to check for a ma ...

Operation check
Inspect driver side seat belt warning light Turn the ignition switch on. When the driver seat belt is not fastened, check that the driver seat belt warning light on the combination meter blinks. When the driver seat belt is fastened, check that the driver seat belt warning light o ...

В© 2011-2024 Copyright www.trav4.net