Toyota RAV4 manuals

Toyota RAV4 Service Manual: Installation

Toyota RAV4. Installation


  1. Install no. 2 Chain sub-assembly

  1. Set the crankshaft key in the left horizontal position.
  2. Turn the cutout of the drive shaft so that it faces upward.

Toyota RAV4. Install no. 2 Chain sub-assembly


  1. Align the yellow mark links with the timing marks of each gear as shown in the illustration.
  2. Install the sprockets onto the crankshaft and oil pump shaft with the chain wrapped on the gears.
  3. Temporarily tighten the oil pump drive shaft sprocket with the nut.
  4. Insert the damper spring into the adjusting hole, and then install the chain tensioner plate with the bolt.

    Torque: 12 n*m (122 kgf*cm, 9 ft.*Lbf)

Toyota RAV4. Install no. 2 Chain sub-assembly


  1. Align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.
  2. Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft gear to lock the gear in position, and then tighten the nut.

    Torque: 29.5 N*m (301 kgf*cm, 22 ft.*Lbf)

  1. Install crankshaft timing sprocket

Toyota RAV4. Install crankshaft timing sprocket


  1. Install no. 1 Chain vibration damper

Toyota RAV4. Install no. 1 Chain vibration damper


  1. Install the chain vibration damper with the 2 bolts.

    Torque: 9.0 N*m (92 kgf*cm, 80 in.*Lbf)

  1. Install chain sub-assembly

Toyota RAV4. Install chain sub-assembly


  1. Set the no. 1 Cylinder to tdc/compression.
  1. Turn the camshafts with a wrench (using the hexagonal lobe) to align the timing marks of the camshaft timing gear with each timing mark located on the no. 1 And no. 2 Bearing caps as shown in the illustration.

Toyota RAV4. Install chain sub-assembly


  1. Using the crankshaft pulley bolt, turn the crankshaft to position the key on the crankshaft upward.

Toyota RAV4. Install chain sub-assembly


  1. Install the chain onto the crankshaft timing sprocket with the gold or orange mark link aligned with the timing mark on the crankshaft.

Toyota RAV4. Install chain sub-assembly


  1. Using sst and a hammer, tap in the crankshaft timing sprocket.

    Sst 09309-37010

Toyota RAV4. Install chain sub-assembly


  1. Align the gold or yellow links with each timing mark located on the camshaft timing gear and sprocket, then install the chain.
  1. Install chain tensioner slipper

Toyota RAV4. Install chain tensioner slipper


  1. Install the chain tensioner slipper with the bolt.

    Torque: 19 n*m (194 kgf*cm, 14 ft.*Lbf)

  1. Install timing chain guide

  1. Install the timing chain guide with the bolt.

    Torque: 9.0 N*m (92 kgf*cm, 80 in.*Lbf)

Toyota RAV4. Install timing chain guide


  1. Install no. 1 Crankshaft position sensor plate

Toyota RAV4. Install no. 1 Crankshaft position sensor plate


  1. Install the sensor plate with the "f" mark facing forward.
  1. Install timing chain cover sub-assembly

Toyota RAV4. Install timing chain cover sub-assembly


  1. Remove any old packing material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.
  2. Apply seal packing (diameter 4.0 To 4.5 Mm (0.157 To 0.177 In.)) As shown in the illustration.

Toyota RAV4. Install timing chain cover sub-assembly


Seal packing:

Toyota genuine seal packing block, three bond 1207b or equivalent

Notice:

  1. Apply a continuous bead of seal packing as shown in the illustration.

Seal packing:

Toyota genuine seal packing block, three bond 1207b or equivalent

Notice:

Toyota RAV4. Install timing chain cover sub-assembly


Toyota RAV4. Install timing chain cover sub-assembly


  1. Install the timing chain cover with the 12 bolts and 2 nuts.

Torque: 9.0 N*m (92 kgf*cm, 80 in.*Lbf) for bolt a

25 N*m (255 kgf*cm, 18 ft.*Lbf) for bolt b

55 N*m (561 kgf*cm, 41 ft.*Lbf) for bolt c

11 N*m (112 kgf*cm, 8 ft.*Lbf) for nut

Hint:

Bolt length:


Toyota RAV4. Install timing chain cover sub-assembly


  1. Using an e10 "torx" socket, install the stud bolt for the v-ribbed belt tensioner

Torque: 21.5 N*m (219 kgf*cm, 16 ft.*Lbf)

  1. Install no. 1 Chain tensioner assembly

Toyota RAV4. Install no. 1 Chain tensioner assembly


  1. Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.

Toyota RAV4. Install no. 1 Chain tensioner assembly


  1. Install a new gasket and the chain tensioner with the 2 nuts.

Torque: 9.0 N*m (92 kgf*cm, 80 in.*Lbf)

Notice:

When installing the chain tensioner, set the hook again if the hook releases the plunger.

  1. Install v-ribbed belt tensioner assembly

Toyota RAV4. Install v-ribbed belt tensioner assembly


  1. Install the v-ribbed belt tensioner with the bolt and nut.

Torque: 59.5 N*m (607 kgf*cm, 44 ft.*Lb

f)

Notice:

Do not lift the engine more than necessary.

  1. Install engine mounting bracket rh

  1. Install the engine mounting bracket rh with the 3 bolts.

Toyota RAV4. Install engine mounting bracket rh


Torque: 55 n*m (561 kgf*cm, 41 ft.*Lbf)

  1. Install crankshaft pulley

Toyota RAV4. Install crankshaft pulley


  1. Using sst, fix the pulley in place and tighten the bolt.

Sst 09213-54015 (91651-60855), 09330-00021 torque: 180 n*m (1,835 kgf*cm, 133 ft.*Lbf)

  1. Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.

Toyota RAV4. Install crankshaft pulley


  1. Turn the crankshaft clockwise, then check that the plunger is extended.

Toyota RAV4. Install crankshaft pulley


  1. Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and oil pan.
  2. Apply a continuous bead of seal packing (diameter 3.0 To 4.0 Mm (0.118 To 0.157 In.)) As shown in the illustration.

Seal packing: toyota genuine seal packing block, three bond 1207b or equivalent

Notice:

  1. install the oil pan to the cylinder block.

Toyota RAV4. Install crankshaft pulley


  1. Uniformly tighten the 12 bolts and 2 nuts in the sequence shown in the illustration.

Torque: 9.0 N*m (92 kgf*cm, 80 in.*Lbf)

Toyota RAV4. Install crankshaft pulley


  1. Place a transmission jack underneath the engine, then put a wooden block on the jack.
  2. Remove the chain block and sling device.
  3. Remove the no. 1 And no. 2 Engine hangers.

Toyota RAV4. Install crankshaft pulley


  1. Install crankshaft position sensor (see page es-402)

  2. Install cylinder head cover sub-assembly

  1. Remove any old packing material from the contact surface.
  2. Apply seal packing to the 2 locations shown in the illustration.

Seal packing: toyota genuine seal packing block, three

Bond 1207b or equivalent

Notice:

Toyota RAV4. Install cylinder head cover sub-assembly


  1. Install the cylinder head cover with the 8 bolts and 2 nuts.

Torque: 11 n*m (112 kgf*cm, 8 ft.*Lbf) for bolt a

14 N*m (143 kgf*cm, 10 ft.*Lbf) for bolt b

11 N*m (112 kgf*cm, 8 ft.*Lbf) for nut

Toyota RAV4. Install cylinder head cover sub-assembly


  1. Install the 2 engine wires with the 2 bolts.

    Torque: 8.4 N*m (86 kgf*cm, 74 in.*Lbf)

Toyota RAV4. Install cylinder head cover sub-assembly


  1. Connect the 2 ventilation hoses to the cylinder head cover.

Toyota RAV4. Install cylinder head cover sub-assembly


  1. Install spark plug (see page em-16)

  2. Install ignition coil assembly (see page ig-9)

  3. Install idler pulley

Toyota RAV4. Install idler pulley


  1. Install the idler pulley with the 2 bolts.

Torque: 60 n*m (612 kgf*cm, 44 ft.*Lbf)

  1. Install engine mounting insulator rh

Toyota RAV4. Install engine mounting insulator rh


  1. Install the engine mounting insulator rh with the 4 bolts and 2 nuts.

Torque: 95 n*m (969 kgf*cm, 70 ft.*Lbf) for bo

95 N*m (969 kgf*cm, 70 ft.*Lbf) for nut a

52 N*m (530 kgf*cm, 38 ft.*Lbf) for nut b

  1. Connect the 2 clamps of the engine wire.
  2. Install the wire harness protector with the bolt.

Toyota RAV4. Install engine mounting insulator rh


  1. Install engine mounting insulator fr

Toyota RAV4. Install engine mounting insulator fr


  1. Install the engine mounting insulator fr with the 2 bolts.

Torque: 95 n*m (969 kgf*cm, 70 ft.*Lbf)

  1. Install the through bolt and nut.

    Torque: 145 n*m (1,479 kgf*cm, 107 ft.*Lbf)

Toyota RAV4. Install engine mounting insulator fr


Hint:

Install the bolt which is used to secure the front engine mounting bracket fr.

  1. Install radiator reservoir

Toyota RAV4. Install radiator reservoir


  1. Install the radiator reservoir with the 2 bolts.

    Torque: 5.0 N*m (51 kgf*cm, 44 in.*Lbf)

  1. Install generator assembly (see page ch-15)

  2. Install fan and generator v belt (see page em-7)

  3. Install front suspension member reinforcement rh (see page em-7)

  4. Install front exhaust pipe (see page ex-4)

  5. Add engine oil (see page lu-4)

  6. Connect cable to negative battery terminal

  7. Check for engine oil leaks

  8. Check for exhaust gas leaks

  9. Install no. 1 Engine cover

Toyota RAV4. Install no. 1 Engine cover


  1. Install the engine cover with the 2 nuts.

    Torque: 7.0 N*m (71 kgf*cm, 62 in.*Lbf)

  1. Install front fender apron rh

  2. Install no. 1 Engine under cover

  3. Install front wheel rh

  4. Install radiator support opening cover

Replacement
Replace timing chain cover oil seal Using a screwdriver and hammer, tap out the oil seal. Place the oil seal retainer on wooden blocks. Apply multi-purpose grease to the lip of a ne ...

Cylinder head
...

Other materials:

Shift position purpose
*1: Shifting the shift lever to d allows the system to select a gear suitable for the driving conditions. Setting the shift lever to d is recommended for normal driving. *2: Selecting shift ranges using s mode restricts the upper limit of the possible gear ranges, controls engine bra ...

Compressor lock sensor circuit
Description This sensor sends 1 pulse per engine revolution to the air conditioning amplifier. If the ratio of the compressor speed divided by the engine speed is smaller than a predetermined value, the air conditioning amplifier turns the compressor off, and the indicator blinks at appro ...

If your vehicle needs to be towed
If towing is necessary, we recommend having your vehicle towed by your toyota dealer or commercial towing service, using a wheel-lift type truck or flatbed truck. Use a safety chain system for all towing, and abide by all state/ provincial and local laws. 2Wd models: if towing your vehicle ...

В© 2011-2024 Copyright www.trav4.net