Toyota RAV4 (XA40) 2013-2018 Service Manual: Installation
- Install rear differential support
- Install the differential support to the differential
carrier with the 4 bolts.
Torque: 98 n*m (999 kgf*cm, 72 ft.*Lbf)
- Install rear differential no. 1 And no. 2 Support
- Install the differential no. 1 And no. 2 Supports with
the 4 bolts to the differential carrier.
Torque: 55 n*m (561 kgf*cm, 41 ft.*Lbf)
- Install rear differential carrier subassembly
- Support the rear differential carrier with a
transmission jack or equivalent
- Apply hypoid gear oil to the splines of the left and
right rear drive shaft inboard joints.
- Align the splines of the rear drive shaft inboard joints
and, using a brass bar and hammer, tap in the left
and right rear drive shafts.
Notice:
- Face the cutout section of the snap ring
downward.
- Do not damage the oil seal during the
insertion.
- Do not strike the tip of the outboard joint with
the hammer.
Hint:
Determine whether or not the rear drive shaft is
completely tapped in by checking for changes in
sound or the reaction force of the brass bar.
- Slowly raise the transmission jack, fix the nuts in
place and install the 3 bolts.
Torque: 86 n*m (877 kgf*cm, 63 ft.*Lbf) for bolt a
140 n*m (1,428 kgf*cm, 103 ft.*Lbf) for
bolt b
Notice:
Tighten the bolts, not the nuts.
- Connect the connector.
- Install the breather tube.
- Connect the harness clamp.
- Install rear suspension member brace lh
- Install the member brace to the suspension member
with the 2 bolts.
Torque: 60 n*m (612 kgf*cm, 44 ft.*Lbf)
- Install rear suspension member brace rh
Hint:
Use the same procedures described for the lh side.
- Temporarily install propeller with
center bearing shaft assembly (see page
pr-5)
- Tighten propeller with center bearing
shaft assembly (see page pr-6)
- Inspect joint angle (see page pr-4)
- Install center exhaust pipe assembly (see
page ex-5)
- Install tailpipe assembly (see page ex-6)
- Install rear wheel
torque: 103 n*m (1,050 kgf*cm, 76 ft.*Lbf)
- Add differential oil
- Add differential oil (see page df-3).
- Check for differential oil leakage
- Check for exhaust gas leakage
If gas is leaking, tighten the areas necessary to stop the
leak. Replace damaged parts as necessary.
Install wiring harness clamp bracket
Install the bracket with the bolt.
Install elbow tube
Install straight pin
Using a plastic hammer, install the 4 straight pins to
the ...
Other materials:
Data list / active test
Read data list
Hint:
Using the intelligent tester's data list allows switch,
actuator and other item values to be read without
removing any parts. Reading the data list early in
troubleshooting is one way to save time.
Connect the intelligent tester (with can vim) to the
dlc3.
Turn ...
Air mix control servo motor (for automatic air conditioning system)
Components
Removal
Remove air conditioning unit
Remove the air conditioning radiator (see page ac-
185).
Remove air mix control servo motor (see
page ac-191)
Inspection
Inspect air mix control servo motor
Inspect the servo motor operation.
Connect ...
Srs warning light does not come on
Description
The srs warning light is located on the combination meter.
When the srs is normal, the srs warning light comes on for approximately 6
seconds after the ignition
switch is turned from off to on, and then goes off automatically.
If there is a malfunction in the srs, the srs warni ...