Toyota RAV4 (XA40) 2013-2018 Service Manual: Installation (2006/01- )
- Install abs and traction actuator assembly with bracket
Notice:
do not remove the hole plug before connecting the brake tube. new actuators are filled with brake fluid.
- Install the actuator with bracket with the 3 nuts.
Torque: 19 n*m (194 kgf*cm, 14 ft.*Lbf)
Hint:
The nuts should be tightened in order from 1 to 3 as shown in the illustration.
Notice:
Be careful not to damage the brake tubes.
- Connect the brake tube clamp to the bracket.
- Connect the connector and push the lock lever downward.
- Connect brake lines
- Using sst, connect the 6 brake lines to the correct locations on the actuator, as shown in the illustration.
Sst 09023-00101
Torque: 15.2 N*m (155 kgf*cm, 11 ft.*Lbf) without sst
14 N*m (144 kgf*cm, 10 ft.*Lbf) with sst
Hint:
Use a torque wrench with a fulcrum length of 30 cm (11.81 In.).
- Fill reservoir with brake fluid (see page br- 6)
- Bleed air from brake master cylinder (see page br-7)
- Bleed air from brake line (see page br-7)
- Bleed air from abs and traction actuator assembly (see page br-8)
- Check brake fluid level in reservoir (see page br-6)
- Check for brake fluid leakage
- Install air cleaner case sub-assembly (for 2az-fe)
- Install the air cleaner case (see page em-105).
Hint:
Refer to the procedures from the installation of the air cleaner case up until the installation of the purge vsv.
- Install air cleaner case (for 2gr-fe)
- Install the air cleaner case (see page em-31).
Hint:
Refer to the procedures from the installation of the air cleaner case up until the installation of the air cleaner cap sub-assembly.
- Connect cable to negative battery terminal
- Check abs and traction actuator assembly with intelligent tester
- Check the abs and traction actuator with the intelligent tester (see page bc-180).
Inspection
- Inspect front speed sensor
- Check the speed sensor. If any of the following occurs, replace the speed sensor with a new one.
- The surface of the speed sensor is cracked, dented, or chipped.
- The connector or wire harness is scratched, cracked, or damaged.
- The speed sensor has been dropped.
Front speed sensor
Components
Removal
Hint:
Use the same procedures for the lh side and rh side.
The procedures listed below are for the lh side.
Disconnect cable from negative battery
terminal
Ca ...
Installation
Hint:
Use the same procedures for the lh side and rh side.
The procedures listed below are for the lh side.
Install speed sensor front lh
Notice:
To prevent interference with other par ...
Other materials:
Diagnosis system
Check dlc3
Check the dlc3:
the power steering ecu uses can (iso11898-1)
and iso9141-2 for communication protocol. The
terminal arrangement of the dlc3 complies with
sae j1962 and matches the iso9141-2 format.
Notice:
*: Before measuring the resistance, leave the
vehicle ...
Selecting the audio
source
Switching between audio sources such as radio and cd are
explained in this section.
Changing audio source
Press the “audio” button to display the audio source selection
screen.
If the audio source selection screen is not displayed, press the “audio”
button again.
Select the d ...
Solar sensor (for automatic air conditioning system)
Components
Removal
Disconnect cable from negative battery
terminal
Caution:
Wait at least 90 seconds after disconnecting the
cable from the negative (-) battery terminal to
prevent airbag and seat belt pretensioner activation.
Remove solar sensor
Using a screwdriver, p ...
