Toyota RAV4 Service Manual: Outer rear view mirror
Components
Removal
Hint:
- Use the same procedures for the lh side and rh side.
- The procedures listed below are for the lh side.
- Remove front door lower frame bracket
garnish lh (see page ed-19)
- Remove front armrest upper base panel
lh (see page ed-19)
- Remove front door trim board subassembly
lh (see page ed-20)
- Remove outer rear view mirror assembly lh
- Disconnect the mirror connector labeled a.
- Remove the 3 screws.
- Remove the outer rear view mirror.
- Remove outer mirror cover lh (w/ mirror
heater)
- Using a moulding remover, detach the 4 claws.
Hint:
Apply protective tape to the mirror body.
- Remove the 2 connectors and disconnect the
mirror.
- Using a screwdriver, detach the 8 claws and remove
the mirror cover.
Hint:
Tape the screwdriver tip before use.
- Remove outer mirror cover lh (w/o mirror
heater)
- Using a moulding remover, detach the 4 claws.
Hint:
Apply protective tape to the mirror body.
- Disconnect the mirror.
- Using a screwdriver, detach the 8 claws and remove
the mirror cover.
Hint:
Tape the screwdriver tip before use.
Inspection
- Inspect outer rear view mirror assembly lh
- Disconnect the mirror connector.
- Apply battery voltage and check the operation of the
mirror.
Ok
If the result is not as specified, replace the mirror
assembly.
- W/ mirror heater:
Check the resistance.
- Measure the resistance between the terminals.
Standard resistance
If the result is not as specified, replace the
outer rear view mirror.
- Connect the cable from the negative battery (-)
terminal to terminal 5 and the positive battery
(+) terminal to terminal 4, then check that the
mirror becomes warm.
Ok:
mirror becomes warm.
Hint:
It takes a short time for the mirror to become
warm.
If the result is not as specified, replace the
outer rear view mirror.
- Inspect outer rear view mirror assembly rh
- Disconnect the mirror connector.
- Apply battery voltage and check the operation of the
mirror.
Ok
If the result is not as specified, replace the mirror
assembly.
- W/ mirror heater:
Check the resistance.
- Measure the resistance between the terminals.
Standard resistance
If the result is not as specified, replace the
outer rear view mirror.
- Connect the cable from the negative battery (-)
terminal to terminal 5 and the positive battery
(+) terminal to terminal 4, then check that the
mirror becomes warm.
Ok:
mirror becomes warm.
Hint:
It takes a short time for the mirror to become
warm.
If the result is not as specified, replace the
outer rear view mirror.
Installation
- Install outer mirror cover lh
- Attach the 8 claws and install the mirror cover.
- After installing the outer mirror cover, check that
there is no gap between the cover and mirror body.
Hint:
If there is a gap between the cover and body, noise
will occur during driving.
- W/ mirror heater:
connect the 2 connectors. Attach the 4 claws to
install the mirror.
- W/o mirror heater:
attach the 4 claws to install the mirror.
- Install outer rear view mirror assembly lh
- Pass the connector labeled a and wire harness of
the mirror through the wire harness hole.
- Temporarily install the mirror by inserting the bosses
on the mirror into the holes on the vehicle.
- Tighten the 3 screws in the sequence shown in the
illustration and install the mirror.
Torque: 9.0 N*m (92 kgf*cm, 80 in.*Lbf)
- Connect the connector labeled a.
- Install front door trim board subassembly
lh (see page ed-33)
- Install front door lower frame bracket
garnish lh (see page ed-35)
Components
Removal
Remove inner rear view mirror assembly
Disengage the 2 claws and separate the inner rear
view mirror cover as shown in the illustration.
Remove the in ...
Inspection
Inspect outer mirror switch assembly
The l position of the left/right adjustment switch:
measure the resistance of the mirror switch.
Standard resistance (for left side)
...
Other materials:
Disposal
Hint:
When scrapping a vehicle equipped with an srs or disposing
of the front passenger side knee airbag, be sure to deploy the
airbag first in accordance with the procedure described
below. If any abnormality occurs with the airbag deployment,
contact the service dept. Of toyota motor sales,
...
Installation
Hint:
Use the same procedures for the rh side and lh side.
The procedures listed below are for the lh side.
When replacing the clip, heat the clip and body using a
heat light.
Standard heating temperature
Notice:
Do not heat the clip and vehicle body excessively.
Replace roof dri ...
Throttle / pedal position sensor / switch "A" circuit range / performance
problem
Hint:
This dtc relates to the throttle position (tp) sensor.
Description
Refer to dtc p0120 (see page es-114).
Monitor description
The ecm uses the tp sensor to monitor the throttle valve opening angle.
This sensor transmits two signals: vta1 and vta2. Vta1 is used to detect the
th ...