Toyota RAV4 Service Manual: Reassembly
Caution:
Wear protective gloves. Sharp areas on the seat frame
(with adjuster) may injure your hands.
Hint:
- Use the same procedures for the rh side and lh side.
- The procedures listed below are for the lh side.
- Install occupant classification ecu (for
driver side) (see page rs-394)
- Install seat position airbag sensor (for
driver side) (see page rs-390)
- Install front seat cushion lower shield lh
- Attach the claw to install the lower shield.
- Install front seat cushion lower shield
rh
Hint:
Use the same procedures described for the lh side.
- Install reclining adjuster upper inside cover lh
- Install the inside cover with the screw.
- Install reclining adjuster upper inside
cover rh
- Install the inside cover with the screw.
- Install reclining adjuster lower inside cover lh
- Attach the claw to install the inside cover.
- Install the screw.
- Install reclining adjuster lower inside cover rh
Hint:
Use the same procedures described for the lh side.
- Install front seatback heater (w/ seat heater system)
- Using a tacker, install the seatback heater to the end
of the seat cover with 6 new tack pins.
Notice:
Do not substitute other metal parts for tack pins.
- Install front seatback cover
Notice:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the
cover.
- Using hog ring pliers, install the seatback cover to
the seatback pad with 11 new hog rings.
- Install the seatback cover (with pad) to the seat
frame (with adjuster).
- W/ front seat side airbag:
fully cover the airbag with the 2 seatback cover
brackets and install the nut.
Torque: 5.5 N*m (56 kgf*cm, 49 in.*Lbf)
Caution:
- For vehicles with side airbags, the seatback
cover must be securely installed. Otherwise,
the side airbags may not deploy properly.
- Make sure that the strap is not twisted after
installing the bracket.
- Install the bracket securely.
- Attach the 4 claws to install the 2 headrest supports.
- W/ seatback board:
attach the hooks.
- W/ seatback board:
using hog ring pliers, install 5 new hog rings.
- W/o seatback board:
using hog ring pliers, install 3 new hog rings.
- W/o seatback board:
close the 2 zippers.
- Install front seatback board subassembly lh (w/ seatback board)
- Push the seatback board in the direction indicated
by the arrow in the illustration to attach the 2 claws.
- Open the lower part of the seatback board. Then
install the seatback board with the 2 screws.
- Install front seat cushion heater (w/ seat heater system)
- Using a tacker, install the seat cushion heater to the
end of the seat cover with 10 new tack pins.
Notice:
Do not substitute other metal parts for tack pins.
- Install front seat cushion cover
- Using hog ring pliers, install the seat cushion cover
to the seat cushion pad with 15 new hog rings.
Notice:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling
the cover.
- Install the seat cushion cover (with pad) to the seat
frame (with adjuster).
- Attach the hooks and install the 2 clips.
- W/ seat heater system:
connect the connector.
- Install front seat inner belt assembly (see page sb-23)
- Install front seat cushion inner shield lh
- Attach the clip and claw to install the inner shield.
- Install the screw.
- Install front seat cushion shield lh (for driver side)
- Attach the 3 claws to install the cushion shield.
- Install the 2 screws.
- Connect the 2 rubber bands of the front seatback
board or front seatback cover to the seat frame (with
adjuster).
- Install front seat cushion shield rh (for front passenger side)
- Attach the 3 claws to install the cushion shield.
- Install the 2 screws.
- Connect the 2 rubber bands of the front seatback
board or front seatback cover to the seat frame (with
adjuster).
- Install reclining adjuster release handle lh (for driver side)
- Attach the claw to install the release handle.
- Install reclining adjuster release handle Rh (for front passenger
side)
Hint:
Use the same procedures described for the driver side.
- Install vertical adjusting handle (for driver side)
- Install the handle with the 2 screws.
- Install vertical adjuster cover lh (for driver side)
- Attach the 2 claws to install the cover.
Caution:
Wear protective gloves. Sharp areas on the seat frame
(with adjuster) may injure your hands.
Hint:
Use the same procedures for the rh side and lh side.
The procedures listed below ar ...
Other materials:
Installation
Install air conditioner unit assembly
Install the a/c unit with the bolt and nut.
Torque: 9.8 N*m (100 kgf*cm, 7 ft.*Lbf)
Install instrument panel reinforcement
Install the instrument panel reinforcement with the 6
bolts.
Torque: 20 n*m (204 kgf*cm, 15 ft.*Lbf)
...
Sensor (motor) failure
Description
When the sliding roof drive gear (sliding roof ecu) detects the motor's
malfunction, and the sliding roof
operation is stopped, dtc b2341 is output. When the sliding roof drive gear
(sliding roof ecu) detects the
gear's malfunction, and the sliding roof operation is stopped, d ...
A/f sensor circuit slow response (bank 1 sensor 1)
Hint:
Sensor 1 refers to the sensor mounted in front of the three-way catalytic
converter (twc) and located
near the engine assembly.
Description
Refer to dtc p2195 (see page es-292).
Monitor description
After the engine is warmed up, the ecm performs air-fuel ratio feedback
contro ...