Toyota RAV4 manuals

Toyota RAV4 Service Manual: Reassembly

Hint:

  1. Install seat lock release band

  1. Install the band with nut.

Hint:

After installing the band, feed it through the seatback frame hole towards the rear of the vehicle.

  1. Install reclining lock release band

Hint:

Use the same procedures described for the lh side.

  1. Install seatback lock control cable assembly

Toyota RAV4. Install seatback lock control cable assembly


  1. Install the cable to the seatback frame as shown in the illustration.
  1. Install rear seat reclining inner cover lh

Toyota RAV4. Install rear seat reclining inner cover lh


  1. Attach the 2 claws to install the inner cover.
  1. Install rear seat reclining inner cover rh

Hint:

Use the same procedures described for the lh side.

  1. Install rear no. 2 Seatback cover

Notice:

Toyota RAV4. Install rear no. 2 Seatback cover


  1. Using hog ring pliers, install the seatback cover to the seatback pad with 3 new hog rings.
  2. Install the seatback cover (with pad) to the seatback frame.

Toyota RAV4. Install rear no. 2 Seatback cover


  1. Attach the 4 claws to install the 2 headrest supports.
  2. Using hog ring pliers, install 19 new hog rings.
  1. Install rear seatback board carpet assembly lh

Toyota RAV4. Install rear seatback board carpet assembly lh


  1. Pass the 2 release bands through the 2 holes in the seatback board carpet.

Toyota RAV4. Install rear seatback board carpet assembly lh


  1. Attach the 9 clips to install the carpet.

Hint:

Make sure that the release band is not inside the seatback board carpet.

  1. Install rear seatback lock control bezel

Toyota RAV4. Install rear seatback lock control bezel


  1. Pass the 2 release bands through the 2 holes in the 2 bezels.
  2. Attach the 2 claws to install the 2 bezels.
  3. Install the 2 screws.
  4. Install the 4 seatback lock hooks.
  1. Install rear no. 2 Seat headrest assembly

  2. Install rear seat cushion wire subassembly

Toyota RAV4. Install rear seat cushion wire subassembly


  1. Install the wire with the nut.

    Torque: 18 n*m (184 kgf*cm, 13 ft.*Lbf)

  1. Install seat lock control cable assembly

Toyota RAV4. Install seat lock control cable assembly


  1. Install the 5 cables to the seat cushion spring as shown in the illustration.

Toyota RAV4. Install seat lock control cable assembly


  1. Clamp the cables to the seat cushion spring with 4 new cable ties as shown in the illustration.

Toyota RAV4. Install seat lock control cable assembly


  1. Cut off the 2 cable ties, as shown in the illustration.
  2. Attach the 2 clamps of the cable tie to the seat cushion spring.
  1. Install rear no. 2 Seat cushion cover lh

Toyota RAV4. Install rear no. 2 Seat cushion cover lh


Notice:

Toyota RAV4. Install rear no. 2 Seat cushion cover lh


  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 5 new hog rings.

Toyota RAV4. Install rear no. 2 Seat cushion cover lh


  1. Attach the hooks and install the seat cushion cover (with pad) to the seat cushion spring.

Toyota RAV4. Install rear no. 2 Seat cushion cover lh


  1. Attach the 5 hooks.
  2. Install the 2 clips.
  1. Install rear no. 2 Seat inner belt assembly lh (see page sb-40)

  2. Remove rear no. 2 Seat cushion assembly

Toyota RAV4. Remove rear no. 2 Seat cushion assembly


  1. Install the seat cushion to the seatback with the 4 bolts.

    Torque: 42 n*m (428 kgf*cm, 31 ft.*Lbf)

Toyota RAV4. Remove rear no. 2 Seat cushion assembly


  1. Connect the seat lock control cable of the rh side to the seatback as shown in the illustration.

Toyota RAV4. Remove rear no. 2 Seat cushion assembly


  1. Connect the seat lock control cable of the back side to the seat cushion as shown in the illustration.
  2. Close the seat cushion cover and install the 2 clips.
  1. Install no. 1 Rear seat reclining cover lh

Toyota RAV4. Install no. 1 Rear seat reclining cover lh


  1. Attach the 5 claws to install the cover.
  2. Install the 2 screws.
  1. Install no. 2 Rear seat reclining cover lh

Toyota RAV4. Install no. 2 Rear seat reclining cover lh


  1. Attach the clip and 5 claws to install the cover.
  2. Install the 2 screws.
Disassembly
Hint: Use the same procedures for the rh side and lh side. The procedures listed below are for the lh side. Remove no. 1 Rear seat reclining cover lh Remove the 2 screws. Using ...

Installation
Hint: Use the same procedures for the rh side and lh side. The procedures listed below are for the lh side. Install no. 2 Seat leg box protector Attach the clip to install the pr ...

Other materials:

Driver side rear airbag sensor circuit malfunction
Description The rear airbag sensor lh consists of parts including the diagnostic circuit and the lateral deceleration sensor. When the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether or not the srs should be activated. Dtc b1630/23 i ...

Driver side seat belt buckle switch circuit malfunction
Description The driver side seat belt buckle switch circuit consists of the center airbag sensor and the front seat inner belt lh. Dtc b1655/37 is recorded when a malfunction is detected in the driver side seat belt buckle switch circuit. Wiring diagram Inspection procedure ...

Removal
Disconnect cable from negative battery terminal Caution: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. Remove no. 1 Engine cover (see page es-410) Remove camshaft timing oil cont ...

В© 2011-2024 Copyright www.trav4.net