Toyota RAV4 manuals

Toyota RAV4 Service Manual: Reassembly (2005/11-2006/01)

  1. Install drive shaft bearing case subassembly

Toyota RAV4. Install drive shaft bearing case subassembly


  1. Using sst and a press, press in the drive shaft bearing case to the inboard joint rh.

Sst 09527-10011, 09710-04081

Notice:

The bearing should be installed completely.

Toyota RAV4. Install drive shaft bearing case subassembly


  1. Using a snap ring expander, install a new drive shaft hole snap ring.
  1. Install front drive shaft dust cover

Toyota RAV4. Install front drive shaft dust cover


  1. Using sst and a press, press in a new drive shaft dust cover.

Sst 09726-40010, 09527-10011

Notice:

Be careful not to damage the dust cover.

  1. Install front drive shaft dust cover rh

  1. Using sst and a press, press in a new drive shaft dust cover until the distance from the tip of the center drive shaft to the drive shaft dust cover reaches the specification, as shown in the illustration.

Toyota RAV4. Install front drive shaft dust cover rh


Sst 09527-10011

Standard distance: 91.0 To 92.0 Mm (3.583 To 3.622 In.)

Notice:

  1. Install front drive shaft dust cover lh

Toyota RAV4. Install front drive shaft dust cover lh


  1. Using sst and a press, press in a new drive shaft dust cover.

Sst 09527-10011

Notice:

  1. Install front drive shaft lh hole snap ring

  1. Install a new hole snap ring.
  1. Install front axle outboard joint boot

Toyota RAV4. Install front axle outboard joint boot


Hint:

Before installing the boots, wrap the spline of the drive shaft with vinyl tape to prevent the boots from being damaged.

  1. Install new parts to the outboard joint shaft in the following order.
  1. No. 2 Outboard joint boot clamp
  2. Outboard joint boot
  3. Outboard joint boot clamp
  1. Pack the outboard joint shaft and boot with grease from the boot kit.

Standard grease capacity: 190 to 200 g (6.7 To 7.1 Oz.)

  1. Install front axle outboard joint boot no. 2 Clamp lh

Caution:

Wear protective gloves while performing the operation and be careful to avoid cutting your hands or other body parts.

Toyota RAV4. Install front axle outboard joint boot no. 2 Clamp lh


  1. Install a new boot clamp to the outboard joint boot and temporarily bend the lever.

Notice:

Toyota RAV4. Install front axle outboard joint boot no. 2 Clamp lh


  1. With the joint on the working surface, use your body weight to press down on the joint with one hand.

    Then, roll the joint forward, as shown in the illustration, and press the lever in until a "click" sound is heard.

Notice:

Toyota RAV4. Install front axle outboard joint boot no. 2 Clamp lh


  1. Using a plastic-faced hammer, fix the buckle into place by tapping it. At the same time, use the plastic-faced hammer to adjust the lift of the lever so that the gaps between the buckle flange and lever end flange become even.

Notice:

Do not damage the boot.

  1. Install front axle outboard joint boot no. 2 Clamp rh

Hint:

Use the same procedures described for the lh side.

  1. Install front axle outboard joint boot clamp lh

Toyota RAV4. Install front axle outboard joint boot clamp lh


Caution:

Wear protective gloves while performing the operation and be careful to avoid cutting your hands or other body parts.

  1. Install a new boot clamp to the outboard joint boot and temporarily bend the lever.

Notice:

When temporarily bending the lever, make sure not to deform the band and lever.

Toyota RAV4. Install front axle outboard joint boot clamp lh


  1. Using water pump pliers, temporarily lock the boot clamp by clamping it down until a "click" sound is heard.

Toyota RAV4. Install front axle outboard joint boot clamp lh


  1. Using a plastic-faced hammer, fix the buckle into place by tapping it. At the same time, use the plastic-faced hammer to adjust the lift of the lever so that the gaps between the buckle flange and lever end flange become even.

Notice:

Do not strike the drive shaft forcefully with the plastic-faced hammer.

  1. Install front axle outboard joint boot rh clamp

Hint:

Use the same procedures described for the lh side.

  1. Install front drive shaft damper lh

Toyota RAV4. Install front drive shaft damper lh


Hint:

Install the damper clamp to outboard joint side.

  1. Install a new drive shaft damper clamp and the drive shaft damper to the drive shaft.
  2. Make sure that the damper is on the shaft groove.
  3. Set the distance, as described below.

Standard distance: 161 to 165 mm (6.339 To 6.496 In.)

  1. Install front drive shaft damper clamp lh

Toyota RAV4. Install front drive shaft damper clamp lh


  1. Hold the front drive shaft lightly in a soft vise.
  2. Install the drive shaft damper clamp to the damper.

Notice:

Be sure to install the clamp in the correct position.

  1. One touch type:
  1. Using a screwdriver, install the drive shaft damper clamp, as shown in the illustration.
  1. Claw engagement type:
  1. Using needle-nose pliers, install the drive shaft damper clamp, as shown in the illustration.
  1. Install front drive inboard joint assembly lh

Toyota RAV4. Install front drive inboard joint assembly lh


  1. Wrap the spline of the outboard joint shaft with vinyl tape to prevent the boots from being damaged.
  2. Install new parts to the outboard joint shaft in the following order.
  1. Inboard joint boot clamp
  2. No. 2 Inboard joint boot clamp
  3. Inboard joint boot
  1. Place the beveled side of the tripod axial spline toward the outboard joint.
  2. Align the matchmarks placed before removal.
  3. Using a brass bar and hammer, tap the tripod joint onto the drive shaft.

Notice:

  1. Pack the inboard joint shaft and boot with grease from the boot kit.

Standard grease capacity: 175 to 185 g (6.2 To 6.5 Oz.)

Toyota RAV4. Install front drive inboard joint assembly lh


  1. Using a snap ring expander, install a new shaft snap ring.
  2. Align the matchmarks, and install the inboard joint to the outboard joint shaft.
  1. Install front drive inboard joint assembly rh

Hint:

Use the same procedures described for the lh side.

  1. Install front axle inboard joint boot

  1. Install the inboard joint boot to the inboard joint.
  1. Install front axle inboard joint boot clamp lh

Toyota RAV4. Install front axle inboard joint boot clamp lh


  1. One touch type:
  1. Using a screwdriver, install the inboard joint boot clamp, as shown in the illustration.

Notice:

Be careful not to damage the boot.

  1. Claw engagement type:
  1. Using needle-nose pliers, install the inboard joint boot clamp, as shown in the illustration.

Notice:

Be careful not to damage the boot.

  1. Install front axle inboard joint boot clamp rh

Hint:

Use the same procedures described for the lh side.

  1. Install front axle inboard joint boot no. 2 Clamp lh

Toyota RAV4. Install front axle inboard joint boot no. 2 Clamp lh


  1. One touch type:
  1. Using a screwdriver, install the no. 2 Inboard joint boot clamp, as shown in the illustration.

Notice:

Be careful not to damage the boot.

  1. Claw engagement type:
  1. Using needle-nose pliers, install the no. 2 Inboard joint boot clamp, as shown in the illustration.

Notice:

Be careful not to damage the boot.

  1. Install front axle inboard joint boot no. 2 Clamp rh

Hint:

Use the same procedures described for the lh side.

  1. Inspect front drive shaft

Toyota RAV4. Inspect front drive shaft


  1. Check that there is no severe play in the radial direction of the outboard joint.
  2. Check that the inboard joint slides smoothly in the thrust direction.
  3. Check that there is no severe play in the radial direction of the inboard joint.

Toyota RAV4. Inspect front drive shaft


  1. Check the boots for damage.

Notice:

Keep the drive shaft assembly level during inspection.

Hint:

For dimension (a), refer to the following values.

Reference value:

585.2 Mm (23.039 In.) For lh side

902 Mm (35.512 In.) For rh side

Disassembly (2006/01- )
Remove front axle inboard joint boot no. 2 Clamp One touch type: using a screwdriver, remove the inboard joint boot clamp, as shown in the illustration. Claw engagement type: usin ...

Reassembly (2006/01- )
Install drive shaft bearing case subassembly (for rh) Install the bearing snap ring. Using sst and a press, press in the drive shaft bearing case to the inboard joint rh. Sst 095 ...

Other materials:

Turn signal light circuit
Description The turn signal flasher relay (marking: flsh) in the main body ecu turns on when it receives signals from the headlight dimmer switch integrated with the turn signal switch, causing the turn signal lights to flash. Wiring diagram Inspection procedure Check operation of t ...

Reassembly
Install front oil pump oil seal Using sst and a hammer, install a new oil seal to the pump. Sst 09350-32014 (09351-32140) Hint: The seal end should be flat with the outer edge of the oil pump. Coat the lip of the oil seal with petroleum jelly. Install front oil pump bo ...

Disposal
Hint: When scrapping a vehicle equipped with an srs or disposing of the steering pad, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the service dept. Of toyota motor sales, u.S.A., Inc. Caution ...

В© 2011-2024 Copyright www.trav4.net