Toyota RAV4 manuals

Toyota RAV4 Service Manual: Road test

  1. Problem symptom confirmation

  1. Based on the result of the customer problem analysis, try to reproduce the symptoms. If the problem is that the transaxle does not shift up, shift down, or the shift point is too high or too low, conduct the following road test referring to the automatic shift schedule and simulate the problem symptoms.
  1. Road test

Notice:

Perform the test at the normal operating atf temperature of 50 to 80°c (122 to 176°f).

  1. D position test

Move the shift lever to d and fully depress the accelerator pedal. Check the following:

  1. Check up-shift operation.

Check that the 1 →2, 2→3 and 3 → o/d upshifts take place at the shift point shown in the automatic shift schedule (see page ss-55).

Hint:

O/d gear up-shift prohibition control

O/d gear lock-up prohibition control

  1. For shift shock and slip.

Check for shock and slip at the 1 → 2, 2 → 3 and 3  →o/d up-shifts.

  1. Check for abnormal noise and vibration.

Check for abnormal noise and vibration when up-shifting from 1 →2, 2 → 3 and 3 →o/d while driving with the shift lever on d, and check while driving in the lock-up condition.

Hint:

The check for the cause of abnormal noise and vibration must be done thoroughly as it could also be due to loss of balance in the differential, torque converter clutch, etc.

  1. Check kick-down operation.

While driving the vehicle in the 2nd, 3rd and o/d gears with the shift lever on d, check that the possible kick-down vehicle speed limits for 2 → 1, 3 → 2 and o/d → 3 kick-downs conform to those indicated in the automatic shift schedule (see page ss-55).

  1. Check for abnormal shock and slip at kick-down.
  2. Check the lock-up mechanism.

Hint:

  1. 3 Position test

Move the shift lever to 3 and fully depress the accelerator pedal. Check the following:

  1. Check up-shift operation.

    Check that the 1 → 2 and 2→ 3 up-shifts take place and that the shift point conforms to the automatic shift schedule (see page ss-55).

  2. Check engine braking.

    While driving the vehicle in the 3rd gear with the shift lever on 3, release the accelerator pedal and check the engine braking effect.

  3. Check for abnormal noises during acceleration and deceleration, and for shock at up-shift and down-shift.
  1. 2 Position test

Move the shift lever to 2 and fully depress the accelerator pedal. Check the following:

  1. Check up-shift operation.

Check that the 1 → 2 up-shift takes place and that the shift point conforms to the automatic shift schedule (see page ss-55).

Hint:

There is no o/d up-shift and lock-up when the shift lever is on 2.

  1. Check engine braking.

    While driving the vehicle in the 2nd gear with the shift lever on 2, release the accelerator pedal and check the engine braking effect.

  2. Check for abnormal noises during acceleration and deceleration, and for shock at up-shift and down-shift.
  1. L position test

Move the shift lever to l and fully depress the accelerator pedal. Check the following:

  1. Check that there is no up-shift.

    While driving the vehicle with the shift lever on l, check that there is no up-shift to 2nd gear.

Hint:

There is no lock-up in l.

  1. Check engine braking.

    While driving the vehicle with the shift lever on l, release the accelerator pedal and check the engine braking effect.

  2. Check for abnormal noises during acceleration and deceleration.
  1. R position test

Move the shift lever to r and lightly depress the accelerator pedal. Check that the vehicle moves backward without any abnormal noise or vibration.

Caution:

Before conducting this test, ensure that no people or obstacles are in the test area.

  1. P position test

Stop the vehicle on an incline (more than 5°). Then move the shift lever to p and release the parking brake. Check that the parking lock pawl holds the vehicle in place.

Parts location
System diagram The configuration of the electronic control system in the u140f automatic transaxle is as shown in the following chart. System description System descript ...

Mechanical system tests
Stall speed test Hint: This test is to check the overall performance of the engine and transaxle. Notice: Do not perform the stall speed test longer than 5 seconds. To ensure safety, ...

Other materials:

Front passenger side satellite sensor bus initialization incomplete
Description When the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether or not the srs should be activated. Dtc b1648/82 is recorded when a malfunction is detected in the rear airbag sensor rh circuit. Wiring diagram Inspection pr ...

Diagnosis system
Description Power door lock control system data can be read in the data link connector 3 (dlc3) of the vehicle. When the system seems to be malfunctioning, use the intelligent tester to check for malfunctions and perform repairs. Check dlc3 The ecu uses iso 15765-4 for communi ...

Installation
Install generator assembly Confirm that the wire harness of the crankshaft position sensor is secured to the wire harness clamp bracket through the back of the rib of the timing chain cover. Install the generator with the 2 bolts. Torque: 21 n*m (215 kgf*cm, 16 ft.*Lb ...

© 2011-2024 Copyright www.trav4.net