Toyota RAV4 Service Manual: Short in driver side curtain shield squib circuit
Description
The driver side curtain shield squib circuit consists of the center airbag
sensor and the curtain shield
airbag lh.
The circuit instructs the srs to deploy when the deployment conditions are met.
These dtcs are recorded when a malfunction is detected in the driver side
curtain shield squib circuit.
Wiring diagram
Inspection procedure
Hint:
- Perform the simulation method by selecting the "check mode" (signal
check) with the intelligent
tester (see page rs-49).
- After selecting the "check mode" (signal check), perform the simulation
method by wiggling each
connector of the airbag system or driving the vehicle on a city or rough
road (see page rs-49).
- Check curtain shield airbag assembly lh (driver side curtain shield
squib)
- Turn the ignition switch off.
- Disconnect the cable from the negative (-) battery
terminal, and wait for at least 90 seconds.
- Disconnect the connector from the curtain shield airbag
lh.
- Connect the white wire side of sst (resistance 2.1 Ù) to
connector c.
Caution:
Never connect a tester to the curtain shield airbag
lh (driver side curtain shield squib) for
measurement, as this may lead to a serious injury
due to airbag deployment.
Notice:
- Do not forcibly insert sst into the terminals of the
connector when connecting.
- Insert sst straight into the terminals of the
connector.
Sst 09843-18060
- Connect the cable to the negative (-) battery terminal,
and wait for at least 2 seconds.
- Turn the ignition switch on, and wait for at least 60
seconds.
- Clear the dtcs (see page rs-49).
- Turn the ignition switch off.
- Turn the ignition switch on, and wait for at least 60
seconds.
- Check the dtcs (see page rs-49).
Ok:
dtc b1830, b1831, b1832, b1833 or 57 is not
output.
Hint:
Dtcs other than dtc b1830, b1831, b1832, b1833 or
57 may be output at this time, but they are not related to
this check.
- Check connector
- Turn the ignition switch off.
- Disconnect the cable from the negative (-) battery
terminal, and wait for at least 90 seconds.
- Disconnect sst from connector c.
- Check that the floor wire connector (on the curtain shield
lh side) is not damaged.
Ok:
lock button is not disengaged, and claw of lock is
not deformed or damaged.
- Check floor wire (driver side curtain shield squib circuit)
- Disconnect the connector from the center airbag sensor.
- Connect the cable to the negative (-) battery terminal,
and wait for at least 2 seconds.
- Turn the ignition switch on.
- measure the voltage of the wire harness side connector.
Standard voltage
- Turn the ignition switch off.
- Disconnect the cable from the negative (-) battery
terminal, and wait for at least 90 seconds.
- Measure the resistance of the wire harness side
connector
Standard resistance
- Release the activation prevention mechanism built into
connector b (see page rs-37).
- Measure the resistance of the wire harness side
connector.
Standard resistance
Replace center airbag sensor assembly
Description
The front passenger side - side squib circuit consists of the center airbag
sensor and the front seat side
airbag rh.
The circuit instructs the srs to deploy when the deployment ...
Description
The front passenger side curtain shield squib circuit consists of the center
airbag sensor and the curtain
shield airbag rh.
The circuit instructs the srs to deploy when the dep ...
Other materials:
Tire inflation pressure
Tire inflation pressure
The recommended cold tire inflation
pressure and tire size are displayed
on the tire and loading
information label.
Inspection and adjustment procedure
Tire valve
Tire pressure gauge
Remove the tire valve cap.
Press the tip of the tire pressure gaug ...
Pressure control solenoid "d" electrical (shift solenoid valve slt)
Description
Refer to dtc p2714 (see page ax-91).
Monitor description
When an open or short in the shift solenoid valve slt circuit is detected,
the ecm interprets this as a fault.
The ecm will illuminate the mil and store the dtc.
Monitor strategy
Typical enabling conditions
...
Ignition key cylinder light
Components
Removal
Disconnect cable from negative battery
Caution:
Wait at least 90 seconds after disconnecting the
cable from the negative (-) battery terminal to
prevent airbag and seat belt pretensioner activation.
Place front wheels facing straight ahead
Remove steering pad ...