Toyota RAV4 Service Manual: Short in driver side squib 2nd step circuit
Description
The driver side squib 2nd step circuit consists of the center airbag sensor,
the spiral cable and the
steering pad.
The circuit instructs the srs to deploy when the deployment conditions are met.
These dtcs are recorded when a malfunction is detected in the driver side squib
2nd step circuit.
Wiring diagram
Inspection procedure
Hint:
- Perform the simulation method by selecting the "check mode" (signal
check) with the intelligent
tester (see page rs-52).
- After selecting the "check mode" (signal check), perform the simulation
method by wiggling each
connector of the airbag system or driving the vehicle on a city or rough
road (see page rs-52).
- Check steering pad (driver side squib 2nd step)
- Turn the ignition switch off.
- Disconnect the cable from the negative (-) battery
terminal, and wait for at least 90 seconds.
- Disconnect the connectors from the steering pad.
- Connect the white wire side of sst to the spiral cable
connector e.
Caution:
Never connect a tester to the steering pad (driver
side squib 2nd step) for measurement, as this may
lead to a serious injury due to airbag deployment.
Notice:
- Do not forcibly insert sst into the terminals of the
connector when connecting.
- Insert sst straight into the terminals of the
connector.
Sst 09843-18060
- Connect the cable to the negative (-) battery terminal,
and wait for at least 2 seconds.
- Turn the ignition switch on, and wait for at least 60
seconds.
- Clear the dtcs (see page rs-49).
- Turn the ignition switch off.
- Turn the ignition switch on, and wait for at least 60
seconds
- Check the dtcs (see page rs-49).
Ok:
dtc b1810, b1811, b1812, b1813 or 53 is not
output.
Hint:
Dtcs other than dtc b1810, b1811, b1812, b1813 or
53 may be output at this time, but they are not related to
this check.
- Check connector
- Turn the ignition switch off.
- Disconnect the cable from the negative (-) battery
terminal, and wait for at least 90 seconds.
- Disconnect sst from the spiral cable.
- Check that the spiral cable connector (on the steering
pad side) is not damaged.
Ok:
lock button is not disengaged, and claw of lock is
not deformed or damaged.
- Check driver side squib 2nd step circuit
- Disconnect the connector from the center airbag sensor.
- Connect the cable to the negative (-) battery terminal,
and wait for at least 2 seconds.
- Turn the ignition switch on.
- Measure the voltage of the wire harness side connector.
Standard voltage
- Turn the ignition switch off.
- Disconnect the cable from the negative (-) battery
terminal, and wait for at least 90 seconds.
- Measure the resistance of the wire harness side
connector.
Standard resistance
- Release the activation prevention mechanism built into
connector b (see page rs-37).
- Measure the resistance of the wire harness side
connector.
Standard resistance
- Check instrument panel wire
- Restore the released activation prevention mechanism
of connector b to its original position.
- Disconnect the instrument panel wire connector from the
spiral cable.
- Connect the cable to the negative (-) battery terminal,
and wait for at least 2 seconds.
- Turn the ignition switch on.
- Measure the voltage of the wire harness side connector.
Standard voltage
- Turn the ignition switch off.
- Disconnect the cable from the negative (-) battery
terminal, and wait for at least 90 seconds.
- Measure the resistance of the wire harness side
connector.
Standard resistance
- Release the activation prevention mechanism built into
connector b (see page rs-37).
- Measure the resistance of the wire harness side
connector.
Standard resistance
Replace spiral cable
Description
The front passenger side squib circuit consists of the center airbag sensor
and the front passenger airbag.
The circuit instructs the srs to deploy when the deployment conditions ...
Description
The front passenger side squib 2nd step circuit consists of the center airbag
sensor and the front
passenger airbag.
The circuit instructs the srs to deploy when the deployment ...
Other materials:
Rear brake flexible hose
Installation
Hint:
Use the same procedures for the lh side and rh side.
The procedures listed below are for the lh side.
Install rear brake tube flexible hose
Notice:
The gasket and union bolt must be used as a set, as
shown in the illustration.
Connect the flexible hose wi ...
For vehicles equipped with catalytic converter caution:
If a large amount of unburned gasoline or gasoline
vapors flow into the converter, it may cause
overheating and create a fire hazard. To prevent this,
observe the following precautions.
Use only unleaded gasoline.
Avoid idling the engine for more than 20 minutes.
Avoid performing unnecess ...
Only rear door rh lock / unlock functions do not operate
Description
The main body ecu receives lock / unlock switch signals and activates the
door lock motor accordingly.
Wiring diagram
Inspection procedure
Inspect rear door with motor lock assembly rh
Apply the battery voltage to the door lock motor and
check the operation of th ...