Toyota RAV4 manuals

Toyota RAV4 Service Manual: Srs warning light does not come on

Description

The srs warning light is located on the combination meter.

When the srs is normal, the srs warning light comes on for approximately 6 seconds after the ignition switch is turned from off to on, and then goes off automatically.

If there is a malfunction in the srs, the srs warning light comes on to inform the driver of a problem.

When terminals tc and cg of the dlc3 are connected, the dtc is displayed by blinking the srs warning light.

The srs is equipped with a voltage-increase circuit (dc-dc converter) in the center airbag sensor in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (dc-dc converter) functions to increase the voltage of the srs to normal voltage.

A malfunction in this circuit is not recorded in the center airbag sensor . The srs warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the srs warning light is transmitted from the center airbag sensor to the combination meter through the multiplex communication system.

Wiring diagram

Toyota RAV4. Srs warning light does not come on


Inspection procedure

  1. Check battery

  1. Measure the voltage of the battery.

Standard voltage: 11 to 14 v



  1. Check connectors

  1. Turn the ignition switch off.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Check that the e19 connectors are properly connected to the center airbag sensor and the combination meter.

Ok: the connectors are properly connected.



  1. Check wire harness (source voltage of combination meter)

Toyota RAV4. Check wire harness (source voltage of combination meter)


  1. Turn the ignition switch off.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Disconnect the connector from the combination meter.
  4. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  5. Turn the ignition switch on.
  6. Measure the voltage of the wire harness side connectors.

Standard voltage


  1. Turn the ignition switch off.
  2. Measure the resistance of the wire harness side connectors.

Standard resistance




  1. Check srs warning light

  1. Turn the ignition switch off.
  2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
  3. Connect the e19 connector to the combination meter.
  4. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
  5. Turn the ignition switch on.
  6. Check the srs warning light condition.

Ok: the srs warning light does not come on.



Replace center airbag sensor assembly

Srs warning light remains on
Description The srs warning light is located on the combination meter. When the srs is normal, the srs warning light comes on for approximately 6 seconds after the ignition switch is turned fro ...

Tc and cg terminal circuit
Description Dtc output mode is set by connecting terminals tc and cg of the dlc3. The dtcs are displayed by blinking the srs warning light. Hint: Make sure that dtc b1281 has not been output. ...

Other materials:

Types of child restraints
Child restraint systems are classified into the following 3 types according to the age and size of the child: Rear facing „o infant seat/convertible seat Forward facing „o convertible seat Booster seat Selecting an appropriate child restraint system Use a child restraint ...

Low pitched horn
Components Removal Remove radiator support opening cover (see page et-4) Remove front fender liner lh (see page et-4) Remove front fender liner rh (see page et-4) Remove front bumper cover (see page et-5) Remove low pitched horn Disconnect the horn connector. Remove th ...

Basic audio operations
Basic audio operations and functions common to each mode are explained in this section. Operating the audio system Press this knob to turn the audio system on and off, and turn it to adjust the volume. Press this button to eject a disc Insert a disc into the disc slot Press to pa ...

© 2011-2024 Copyright www.trav4.net