Toyota RAV4 manuals

Toyota RAV4 Service Manual: Steering gear

Components

Toyota RAV4. Steering gear


Toyota RAV4. Steering gear


Removal

  1. Position front wheels facing straight ahead

  2. Disconnect cable from negative battery terminal

Caution:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. Remove front wheel

  2. Disconnect tie rod end sub-assembly lh

Toyota RAV4. Disconnect tie rod end sub-assembly lh


  1. Remove the cotter pin and castle nut.
  2. Using sst, disconnect the tie rod end from the steering knuckle.

Sst 09628-62011

Notice:

Do not damage the tie rod end dust cover.

  1. Disconnect tie rod end sub-assembly rh

Hint:

Use the same procedure for the rh side as for the lh side

  1. Remove column hole cover silencer sheet

Toyota RAV4. Remove column hole cover silencer sheet


  1. Remove the floor carpet, 2 clips and column hole cover silencer.
  1. Disconnect steering sliding yoke subassembly

Toyota RAV4. Disconnect steering sliding yoke subassembly


  1. Use a seat belt to fix the steering wheel in place to avoid breakage of the spiral cable.

Toyota RAV4. Disconnect steering sliding yoke subassembly


  1. Place matchmarks on the sliding yoke of the steering intermediate shaft.
  2. Remove the bolt and disconnect the sliding yoke.
  1. Disconnect no. 1 Steering column hole cover sub-assembly

Toyota RAV4. Disconnect no. 1 Steering column hole cover sub-assembly


  1. Remove clip a, detach clip b from the body and disconnect the no. 1 Steering column hole cover.

Notice:

Do not damage clips a and b.

  1. Remove engine assembly with transaxle

  1. Remove the engine with transaxle (see page em- 98).
  1. Remove no. 1 Steering column hole cover sub-assembly

  1. Remove the clamp and disconnect the column hole cover from the steering gear.
  1. Remove intermediate shaft

Toyota RAV4. Remove intermediate shaft


  1. Place matchmarks on the intermediate shaft of the steering gear.
  2. Remove the bolt and disconnect the steering intermediate shaft from the steering gear.
  1. Remove steering gear assembly

Toyota RAV4. Remove steering gear assembly


  1. Remove the 2 bolts, 2 nuts and steering gear from the suspension crossmember.

Notice:

Keep the nut from rotating while turning the bolt.

Installation

  1. Install steering gear assembly

Toyota RAV4. Install steering gear assembly


  1. Install the steering gear onto the front suspension crossmember with the 2 bolts and 2 nuts.

Torque: 138 n*m (1407 kgf*cm, 102 ft.*Lbf)

Notice:

Keep the nut from rotating while turning the bolt.

  1. Install intermediate shaft

Toyota RAV4. Install intermediate shaft


  1. Align the matchmarks and install the intermediate shaft onto the steering gear.

Torque: 35 n*m (360 kgf*cm, 26 ft.*Lbf)

  1. Install no. 1 Steering column hole cover sub-assembly

  1. Install the column hole cover onto the steering gear with a new clamp.
  1. Install engine assembly with transaxle

  1. Install the engine with transaxle (see page em-105).
  1. Install no. 1 Steering column hole cover sub-assembly

Toyota RAV4. Install no. 1 Steering column hole cover sub-assembly


  1. Attach clip b onto the body portion and install the no. 1 Hole cover onto the body portion with clip a.

Notice:

Make sure that the lip portion of the no. 1 Hole cover is not damaged.

  1. Connect steering sliding yoke subassembly

Toyota RAV4. Connect steering sliding yoke subassembly


  1. Align the matchmarks and install the sliding yoke onto the intermediate shaft.

Torque: 35 n*m (360 kgf*cm, 26 ft.*Lbf)

  1. Install column hole cover silencer sheet

Toyota RAV4. Install column hole cover silencer sheet


  1. Install the column hole cover silencer sheet with the 2 clips.
  2. Install the floor carpet.
  1. Connect tie rod end sub-assembly lh

Toyota RAV4. Connect tie rod end sub-assembly lh


  1. Connect the tie rod end onto the steering knuckle with the castle nut.

Torque: 49 n*m (500 kgf*cm, 36 ft.*Lbf)

Notice:

If the holes for the clip are not aligned, tighten the nut up to 60Рfurther.

  1. Install a new cotter pin.
  1. Connect tie rod end sub-assembly rh

Hint:

Use the same procedure for the rh side as for the lh side.

  1. Install front wheel torque: 103 n*m (1,050 kgf*cm, 76 ft.*Lbf)

  2. Connect cable to negative battery terminal

  3. Position front wheels facing straight ahead

  4. Inspect and adjust front wheel alignment

  1. Inspect and adjust the wheel alignment (see page sp-3).
Eps warning light circuit
Description If the power steering ecu detects a malfunction, the p/s warning light comes on. At this time, the power steering ecu stores a dtc in its memory. Wiring diagram Inspection proced ...

Power steering ecu
Components Removal Disconnect cable from negative battery terminal Remove instrument panel sub-assembly upper Remove the instrument panel (see page ip-4). Remove power steer ...

Other materials:

Short in front driver side pretensioner squib circuit
Description The driver side front pretensioner squib circuit consists of the center airbag sensor and the front seat outer belt lh. This circuit instructs the srs to deploy when the deployment conditions are met. These dtcs are recorded when a malfunction is detected in the front prete ...

Torque converter clutch solenoid circuit
Description The shift solenoid valve dsl is turned on and off by signals from the ecm to control the hydraulic pressure acting on the lock-up relay valve, which then controls operation of the lock-up clutch. Fail-safe function: if the ecm detects a malfunction, it turns the shift sol ...

Problem symptoms table
Hint: Use the table below to help determine the cause of the problem symptom. The potential causes of the symptoms are listed in order of probability in the "suspected area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace p ...

© 2011-2024 Copyright www.trav4.net