Toyota RAV4 manuals

Toyota RAV4 Service Manual: Valve clearance

Adjustment

  1. Disconnect cable from negative battery terminal

Caution:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. Remove front wheel rh

  2. Remove no. 1 Engine under cover

  3. Remove front fender apron rh

  4. Remove no. 1 Engine cover (see page em-22)

  5. Remove ignition coil assembly (see page ig-9)

  6. Remove spark plug

  1. Remove the 4 spark plugs.
  1. Remove cylinder head cover sub-assembly (see page em-24)

  2. Set no. 1 Cylinder to tdc/compression (see page em-25)

  3. Check valve clearance

  1. Check only the valves indicated.
  1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

Toyota RAV4. Check valve clearance


Standard valve clearance (cold)


  1. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve clearance lifters.
  1. Turn the crankshaft 1 revolution (360°) and set the no. 4 Cylinder to the tdc/compression.
  2. Check only the valves indicated.
  1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

Toyota RAV4. Adjustment


Standard valve clearance (cold) 


  1. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.
  1. Adjust valve clearance

  1. Remove the no. 2 Camshaft (see page em-60).
  2. Remove the camshaft (see page em-61).
  3. Remove the valve lifters.
  4. Using a micrometer, measure the thickness of the removed valve lifters.
  5. Calculate the thickness of a new lifter so that the valve clearance comes within the specified values.

Toyota RAV4. Adjust valve clearance


New lifter thickness


Calculation example (intake):

  1. Measured intake valve clearance = 0.40 Mm (0.0158 In.) (Measured - specification = excess clearance) (a)0.40 Mm (0.0158 In.) - 0.24 Mm (0.0095 In.) = 0.16 Mm (0.0063 In.)
  2. Measured used lifter thickness = 5.250 Mm (0.2067 In.)
  3. New lifter thickness = 5.410 Mm (0.2130 In.) (Excess clearance + used lifter thickness = ideal new lifter) (a)0.16 Mm (0.0063 In.) + 5.250 Mm (0.2067 In.) = 5.410 Mm (0.2130 In.)
  4. Closest new lifter = 5.420 Mm (0.2134 In.) – Select no. 42 Lifter
  1. Select a new lifter with a thickness as close as possible to the calculated values.

Hint:

Toyota RAV4. Adjust valve clearance


  1. Valve lifter selection chart (intake).

Toyota RAV4. Adjust valve clearance


Toyota RAV4. Adjust valve clearance


Standard intake valve clearance (cold): 0.19 To 0.29 Mm (0.0075 To 0.0114 In.)

Example:

The 5.250 Mm (0.2067 In.) Lifter is installed, and the measured clearance is 0.400 Mm (0.0157 In.).

Replace the 5.250 Mm (0.2067 In.) Lifter with a new no. 42 Lifter.

  1. Valve lifter selection chart (exhaust).

Toyota RAV4. Valve lifter selection chart (exhaust).


Toyota RAV4. Valve lifter selection chart (exhaust).


Standard exhaust valve clearance (cold): 0.38 To 0.48 Mm (0.0150 To 0.0189 In.)

Example:

The 5.340 Mm (0.2102 In.) Lifter is installed, and the measured clearance is 0.430 Mm (0.0169 In.).

Replace the 5.340 Mm (0.2102 In.) Lifter with a new no. 42 Lifter.

  1. Install the selected valve lifter.
  1. Install camshaft

  1. Apply a light coat of engine oil to the journal portion of the camshaft.
  2. Install the timing chain onto the camshaft timing gear with the paint mark aligned with the timing mark in the camshaft timing gear as shown in the illustration.

Toyota RAV4. Install camshaft


  1. Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps into the cylinder head.
  2. Apply a light coat of engine oil on the threads and under the heads of the bearing cap bolts.

Toyota RAV4. Install camshaft


Toyota RAV4. Install camshaft


  1. Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

Torque: 29.5 N*m (301 kgf*cm, 22 ft.*Lbf) for no.

1 Bearing cap

9.0 N*m (92 kgf*cm, 80 in.*Lbf) for no. 3 Bearing cap

  1. Install no. 2 Camshaft

Toyota RAV4. Install no. 2 Camshaft


  1. Apply a light coat of engine oil to the journal portion of the no. 2 Camshaft.
  2. Put the no. 2 Camshaft on the cylinder head with the paint mark of the chain aligned with the timing mark on the camshaft timing sprocket.
  3. While holding the no. 2 Camshaft by hand, temporarily tighten the camshaft timing sprocket set bolt.

Toyota RAV4. Install no. 2 Camshaft


  1. Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.
  2. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

Toyota RAV4. Install no. 2 Camshaft


Toyota RAV4. Install no. 2 Camshaft


  1. Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

Torque: 29.5 N*m (301 kgf*cm, 22 ft.*Lbf) for no.

2 Bearing cap

9.0 N*m (92 kgf*cm, 80 in.*Lbf) for no. 3 Bearing cap

Toyota RAV4. Install no. 2 Camshaft


  1. While holding the camshaft with a wrench, tighten the camshaft timing sprocket set bolt.

Torque: 54 n*m (551 kgf*cm, 40 ft.*Lbf)

Notice:

Be careful not to damage the valve lifter.

Toyota RAV4. Install no. 2 Camshaft


  1. Check that the paint marks on the chain are aligned with the timing marks on the camshaft timing gear and camshaft timing sprocket. Also, check that the crankshaft pulley groove is aligned with the timing mark "0" of the timing chain cover.
  1. Install no. 1 Chain tensioner

Toyota RAV4. Install no. 1 Chain tensioner


  1. Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.
  2. Install a new gasket and the chain tensioner with the 2 nuts

Toyota RAV4. Install no. 1 Chain tensioner


Torque: 9.0 N*m (92 kgf*cm, 80 in.*Lbf)

Notice:

When installing the chain tensioner, set the hook again if the hook releases the plunger.

  1. Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.

Toyota RAV4. Install no. 1 Chain tensioner


  1. Turn the crankshaft clockwise, then check that the plunger is extended.

Toyota RAV4. Install no. 1 Chain tensioner


  1. Install cylinder head cover sub-assembly (see page em-40)

  2. Install spark plug

  1. Install the 4 spark plugs.

Torque: 25 n*m (255 kgf*cm, 18 ft.*Lbf)

  1. Install ignition coil assembly (see page ig-9)

  2. Connect cable to negative battery terminal

  3. Check for engine oil leaks

  4. Install no. 1 Engine cover (see page em-43)

  5. Install front fender apron rh

  6. Install no. 1 Engine under cover

  7. Install front wheel rh

Installation
Install fan and generator v belt Using sst and 19 mm socket wrench, loosen the vribbed belt tensioner arm clockwise, then install the fan and generator v belt. Sst 09216-42010 Not ...

Timing chain
...

Other materials:

Torque converter and drive plate
Inspection Inspect torque converter clutch assembly Inspect the one-way clutch. Install sst to the inner race of the one-way clutch. Sst 09350-32014 (09351-32010) Set sst so that it fits in the notch of the converter hub and in the outer race of the oneway clutch. ...

Clock
The clock can be adjusted by pressing the buttons. Adjusts the hours. Adjusts the minutes. The clock is displayed when Vehicles without a smart key system The engine switch is in the “acc” or “on” position. Vehicles with a smart key system The engine switch is in a ...

Emergency flashers
The emergency flashers are used to warn other drivers when the vehicle has to be stopped in the road to a breakdown, etc. Press the switch. All the turn signals will flash. To turn them off, press the switch once again. Emergency flashers If the emergency flashers are used for a long ...

© 2011-2024 Copyright www.trav4.net