Toyota RAV4 manuals

Toyota RAV4 Service Manual: Diagnosis system

  1. Check dlc3

Toyota RAV4. Check dlc3


The ecm uses iso 15765-4 for communication. The terminal arrangement of the dlc3 complies with sae j1962 and matches the iso 15765-4 format.

Toyota RAV4. Check dlc3


Toyota RAV4. Check dlc3


If the result is not as specified, the dlc3 may have a malfunction. Repair or replace the harness and connector.

Hint:

Connect the cable of the intelligent tester (with can vim) to the dlc3, turn the ignition switch on and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem wither with the vehicle or with the tester.

  1. Diagnosis system

  1. Warning light

Toyota RAV4. Diagnosis system


  1. The tire pressure warning light blinks when there is a malfunction in the tire pressure warning system.

Notice:

When the malfunction has been corrected, the tire pressure warning light does not turn on.

  1. Dtcs (normal mode)
  1. Dtcs are memorized in the tire pressure warning ecu. These dtcs can be read by checking the blinks of the tire pressure warning light or by using the intelligent tester (see page tw-20).
  1. Test mode
  1. By switching from normal mode to test mode (input signal check), you can inspect the tire pressure monitor receiver, each tire pressure warning valve and transmitter and vehicle speed sensor (see page tw-12).
  1. Check tire pressure warning light

Toyota RAV4. Check tire pressure warning light


  1. Turn the ignition switch on.
  2. Check that the tire pressure warning light turns on for 3 seconds.

    If the warning check result is not normal, proceed to the troubleshooting for the tire pressure warning light circuit.


  1. Tire pressure warning light chart

Hint:

The table below indicates the state of the tire pressure warning light after the ignition switch is turned on.

Toyota RAV4. Tire pressure warning light chart


Toyota RAV4. Tire pressure warning light chart


*1: Turns on and turns off repeatedly at 0.5 Second intervals.

Toyota RAV4. Tire pressure warning light chart


*2: Turns on and turns off repeatedly at 0.125 Second intervals.

Toyota RAV4. Tire pressure warning light chart


*3: Turns on and turns off repeatedly at 0.25 Second intervals.

Dtc check / clear

  1. Dtc check (using intelligent tester)

Toyota RAV4. Dtc check (using intelligent tester)


  1. Connect the intelligent tester (with can vim) to the dlc3.
  2. Turn the ignition switch on.
  3. Read the dtcs following the prompts on the tester screen.

Hint:

Refer to the intelligent tester operator's manual for further details.

  1. Check dtc (using sst check wire)

Toyota RAV4. Check dtc (using sst check wire)


  1. Using sst, connect terminals 13 (tc) and 4 (cg) of the dlc3.

Sst 09843-18040

  1. Turn the ignition switch on.

Toyota RAV4. Check dtc (using sst check wire)


  1. Read and record any dtcs from the tire pressure warning light on the combination meter. Refer to the illustration for examples of a normal system code and dtcs 13 and 33.

Hint:

  1. Refer to the diagnostic trouble code chart for dtc information (see page tw-22).
  2. After completing the check, turn the ignition switch off and remove sst from the dlc3.
  1. Clear dtc (using intelligent tester)

Toyota RAV4. Clear dtc (using intelligent tester)


Hint:

After repairing the malfunctions, clear the dtcs.

  1. Connect the intelligent tester (with can vim) to the dlc3.
  2. Turn the ignition switch on.
  3. Erase the dtcs following the prompts on the tester screen.

Hint:

Refer to the intelligent tester operator's manual for further details.

Terminals of ecu
Check tire pressure warning ecu Disconnect the e56 ecu connector. Measure the voltage and resistance of the wire harness side connector. If the result is not as specified, ther ...

Data list / active test
Read data list Hint: Using the intelligent tester's data list allows switch, actuator and other item values to be read without removing any parts. Reading the data list early in troubleshoot ...

Other materials:

How to proceed with troubleshooting
Hint: Use the procedure to troubleshoot the power door lock control system. *: Use the intelligent tester. Vehicle brought to workshop Inspect battery voltage Standard voltage: 11 to 14 v If the voltage is below 11 v, recharge or replace the battery before proceeding. ...

List of storage features
Glove box Bottle holders Console box Cup holders Storage boxes Caution Items that should not be left in the storage spaces Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: Glasses may b ...

Short in front passenger side curtain shield squib circuit
Description The front passenger side curtain shield squib circuit consists of the center airbag sensor and the curtain shield airbag rh. The circuit instructs the srs to deploy when the deployment conditions are met. These dtcs are recorded when a malfunction is detected in the front p ...

В© 2011-2019 Copyright www.trav4.net