Toyota RAV4 (XA40) 2013-2018 Service Manual: Operation check
- Illuminated entry system operation check
- The illuminated entry system controls the following
lights:
- Ignition key cylinder light*1 or transponder key
amplifier*2
- Foot light
- Map light and room light
Hint:
*1: W/o engine immobiliser system
*2: W/ engine immobiliser system
- Check that the lights come on when unlocking any
of the doors that are closed and locked with the
ignition switch off. Then check that the lights fade
out under the following conditions:
- Leave the doors unlocked for 15 seconds.
- Turn the ignition switch acc or on.
- Lock all the doors.
- Check that the lights stay on for at least 15 seconds
after opening any of the doors before fading out.
Then check that the lights fade out 15 seconds after
closing all the doors.
- Check that the lights stay lit after turning the ignition
switch off with all the doors closed and the ignition
switch in the acc or on position. Then check that
the lights fade out under the following conditions:
- Leave the doors unlocked for 15 seconds.
- Turn the ignition switch acc or on.
- Lock all the doors.
- Check that the lights stay on for at least 15 seconds
after opening any of the doors. Then check that the
lights fade out 15 seconds after closing all the
doors.
- Check that the lights come on when opening any of
the doors and fade out when closing and locking all
the doors or turning the ignition switch to the acc or
on position.
- Foot light operation check
- Check that the lights come on when unlocking any
of the doors that are closed and locked with the
ignition switch off. Then check that the lights fade
out under the following conditions:
- Leave the doors unlocked for 15 seconds.
- Lock all the closed doors and turn the ignition
switch off
- Check that the lights stay on for at least 15 seconds
under the following conditions before going off.
- Turn the ignition switch to the on position, and
move the shift lever to the p position.
- Open any of the doors.
- Check that the lights dim before going off when
turning the ignition switch on and shifting the shift
lever into any position other than p.
- Check the conditions below before the lights go off.
- The lights dim when shifting the shift lever into a
position other than p and closing all the doors
with the ignition switch on.
- The lights come on for 15 seconds and fade out
when shifting the shift lever into the p position
and closing all the doors with the ignition switch
off.
- Check that the lights come on after opening any of
the doors.
- Check that the lights fade out 15 seconds after
closing all the doors, or locking all the doors.
- Check that the lights come on gradually with the
ignition switch on and the shift lever in the p
position.
- Check that the lights dim when shifting the shift
lever from p into another position with all the doors
closed.
- Check that the lights stay dimmed with the ignition
switch on and the shift lever in a position other than
p.
- Battery saver operation check
- Turn the ignition switch off and close all the doors.
- Open any door to turn the room light on, and leave it
open. Check that the light goes off after about 20
minutes.
- After the room light goes off, close the driver's door.
- Open any door to turn the room light on, and then
open another door. Check that the room light goes
off within 20 minutes after opening the doors.
- Close all the doors. Open any door to turn the room
light on. Check that the room light goes off within 20
minutes.
- Light auto turn off operation check
- Turn the ignition switch on, and turn the light
control switch to the tail or head position.
- Turn the ignition switch off and open the driver's
door, and check that the headlights go off after
about 30 seconds.
- Turn the ignition switch to the on position, and turn
the light control switch to the tail or head position.
- Turn the ignition switch off and open the driver's
door. Before the headlight goes off after about 30
seconds, lock all the doors and press the lock
switch on the wireless transmitter. Check that the
headlights go off immediately.
- Daytime running light operation check
- Check that the headlights come on when the light
control switch is off with the engine running and the
parking brake released. Then check that the lights
go off under the following conditions:
- Turn the light control switch to the tail or head
position.
- Turn the ignition switch off. Check that the
headlights go off immediately.
Hint:
Use these procedures to troubleshoot the lighting system.
*: Use the intelligent tester.
Vehicle brought to workshop
Inspect battery voltage
Standard voltage:
11 to 14 v
...
Hint:
The following items can be customized.
Notice:
When the customer requests a change in a function,
first make sure that the function can be customized.
Be sure to make a note of the cur ...
Other materials:
Front occupant classification sensor rh collision detection
Description
Dtc b1786 is output when the occupant classification ecu receives a collision
detection signal sent by
the front occupant classification sensor rh when an accident occurs.
Dtc b1786 is also output when the front seat assembly rh is subjected to a
strong impact, even if an
a ...
Using the interior lights
Interior lights list
Interior lights
Interior/personal lights
Engine switch light (if equipped)
Cup holder light (if equipped)
Interior lights
Front
Off
Door position
The interior lights come on when
a door is opened. They turn off
when the doors are closed.
On
...
Front speed sensor
Components
Removal
Hint:
Use the same procedures for the lh side and rh side.
The procedures listed below are for the lh side.
Disconnect cable from negative battery
terminal
Caution:
Wait at least 90 seconds after disconnecting the
cable from the negative (-) battery termin ...